Order Products : sales@su-jiao.com
Dynaflex™ G7990-9001-02
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | Dynaflex™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | AAaPIV_Dynaflex-G7990-9001-02.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
Dynaflex™ G7990-9001-02 is an easy processing, general purpose TPE designed for a wide variety of applications.
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.17 | g/cm³ | ASTM D792 |
| Molding Shrinkage - Flow | 0.80 - 1.4 | % | ASTM D955 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 10 sec) | 93 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ASTM D412 | ||
| 100% strain, 23°C | 5.62 | MPa | ASTM D412 |
| 300% strain, 23°C | 6.62 | MPa | ASTM D412 |
| Tensile Strength (Break, 23°C) | 10.7 | MPa | ASTM D412 |
| Tensile Elongation (Break, 23°C) | 610 | % | ASTM D412 |
| Tear Strength 1(23°C) | 60.4 | kN/m | ASTM D624 |
| Compression Set (23°C, 22 hr) | 50 | % | ASTM D395B |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Apparent Viscosity (200°C, 11200 sec^-1) | 15.7 | Pa·s | ASTM D3835 |
| Additional Information |
|---|
| Dynaflex™ G7990-9001-02 can be recycled as a filler or impact modifier for polyolefins, or can be recycled by grinding and reintroduction to the molding process. Similar to PP or PE recycling process, if separated appropriately, it can be recycled many times.Municipality waste stream recycle code is "7" which is designated for "Other".Please contact GLS Thermoplastic Elastomers for a copy of our Recyclability Compliance letter. |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Suggested Max Regrind | 20 | % | |
| Rear Temperature | 166 - 188 | °C | |
| Middle Temperature | 177 - 188 | °C | |
| Front Temperature | 188 - 227 | °C | |
| Nozzle Temperature | 188 - 227 | °C | |
| Mold Temperature | 15.6 - 37.8 | °C | |
| Back Pressure | 0.00 - 0.827 | MPa | |
| Screw Speed | 40 - 100 | rpm |
| Injection instructions |
|---|
| Purge thoroughly before and after use of this product with a low flow (0.5 - 2.5 MFR) polyethylene (PE) or polypropylene (PP).Regrind levels up to 20% can be used with Dynaflex™ G7990-9001-02 with minimal property loss, provided that the regrind is free of contamination. To minimize losses during molding, the melt temperature should remain as low as possible. The final determination of regrind effectiveness should be determined by the customer.Dynaflex™ G7990-9001-02 has excellent melt stability. Maximum residence times may vary, depending on the size of the barrel. Generally, the barrel should be emptied if it is idle for periods of 8 - 10 minutes or longer.Drying is not RequiredInjection Speed: 1 to 3 in/sec1st Stage - Boost Pressure: 350 to 900 psi2nd Stage - Hold Pressure: 30% of BoostHold Time (Thick Part): 3 to 10 secHold Time (Thin Part): 1 to 3 sec |
| Note Message | |
|---|---|
| 1 . | 2 hr |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| SCHULAMID® 66 MW 30 FR 4 K2031 | A. Schulman Europe | Nylon 66 | SCHULAMID® |
| Amodel® A-1130 FW | Solvay Specialty Polymers | PPA | Amodel® |
| Dryflex® 422501S | ELASTO | SBS | Dryflex® |
| Hifax CA244 | LyondellBasell Industries | TPO (POE) | Hifax |
| Latilon 28D G/30 | LATI S.p.A. | PC | Latilon |
