Category: | PARA , Polyarylamide |
Manufacturer: | Solvay Specialty Polymers |
Trademark: | Ixef® |
Fillers: | - |
Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
Delivery Terms | FOB, CIF, DAP, DAT, DDP |
PDF: | zec6dv_IxefBM1524.pdf ![]() |
PRICE: | Order Products email sales@su-jiao.com |
Message |
---|
Ixef 1524 is a 50% glass fiber reinforced, halogen-free flame retardant polyacrylamide with high strength, high rigidity, good surface gloss and excellent creep resistance. -black: Ixef 1524/9008 -customers can color by themselves |
General Information | |
---|---|
Filler / Reinforcement |
|
Additive |
|
Features |
|
Uses |
|
RoHS Compliance |
|
Appearance |
|
Forms |
|
Processing Method |
|
Physical | Nominal Value | Unit | Test Method |
---|---|---|---|
Density | 1.69 | g/cm³ | ISO 1183 |
Water Absorption (Balanced, 65% RH) | 0.28 | % | ISO 62 |
Mold shrinkage- Flow | 0.10 - 0.30 | % | Internal method |
Electrical | Nominal Value | Unit | Test Method |
---|---|---|---|
Comparative Tracking Index | PLC 0 | UL 746 |
Flammability | Nominal Value | Unit | Test Method |
---|---|---|---|
Vertical combustion-60 seconds (8.89cm) 1 | 5.0 | sec | DMS 1510 |
Toxic gas emission | BSS 7239/ATS 1000/ABD 0031 | ||
CO | 100 | ppm | BSS 7239/ATS 1000/ABD 0031 |
HCL | ppm | BSS 7239/ATS 1000/ABD 0031 | |
HCN | 15 | ppm | BSS 7239/ATS 1000/ABD 0031 |
HF | ppm | BSS 7239/ATS 1000/ABD 0031 | |
NO + NO2 | ppm | BSS 7239/ATS 1000/ABD 0031 | |
SO2 | ppm | BSS 7239/ATS 1000/ABD 0031 |
Mechanical | Nominal Value | Unit | Test Method |
---|---|---|---|
Tensile Modulus | 20000 | MPa | ISO 527-2 |
Tensile Strength (Yield) | 248 | MPa | ASTM D638 |
Tensile Elongation (Break) | 2.3 | % | ASTM D638 |
Flexural Modulus | 19300 | MPa | ASTM D790 |
Flexural Strength (Yield) | 376 | MPa | ASTM D790 |
Compressive Modulus | 16500 | MPa | ASTM D695 |
Compressive Strength | 328 | MPa | ASTM D695 |
Impact | Nominal Value | Unit | Test Method |
---|---|---|---|
Notched Izod Impact | 120 | J/m | ASTM D256 |
Thermal | Nominal Value | Unit | Test Method |
---|---|---|---|
Heat Deflection Temperature (1.8 MPa, Unannealed) | 227 | °C | ISO 75-2/A |
Electrical | Nominal Value | Unit | Test Method |
---|---|---|---|
Dielectric Constant 2(2.40 GHz) | 4.44 | ASTM D2520 | |
Dissipation Factor 3(2.40 GHz) | 0.012 | ASTM D2520 | |
Comparative Tracking Index (CTI) (3.00 mm) | > 600 | V | UL 746 |
Comparative Tracking Index | > 600 | V | IEC 60112 |
High Amp Arc Ignition (HAI) | UL 746 | ||
0.400 mm | 37.6 | UL 746 | |
0.750 mm | 53.6 | UL 746 | |
1.50 mm | 70.2 | UL 746 | |
3.00 mm | 95.4 | UL 746 | |
High Amp Arc Ignition (HAI) | UL 746 | ||
0.40 mm | PLC 2 | UL 746 | |
0.75 mm | PLC 2 | UL 746 | |
1.5 mm | PLC 1 | UL 746 | |
3.0 mm | PLC 1 | UL 746 | |
High Voltage Arc Resistance to Ignition (HVAR) (3.00 mm) | PLC 0 | UL 746 | |
High Voltage Arc Tracking Rate (HVTR) (3.00 mm) | PLC 0 | UL 746 | |
Hot-wire Ignition (HWI) | UL 746 | ||
0.400 mm | 95 | sec | UL 746 |
0.750 mm | > 120 | sec | UL 746 |
1.50 mm | > 120 | sec | UL 746 |
3.00 mm | > 120 | sec | UL 746 |
Hot-wire Ignition (HWI) | UL 746 | ||
0.40 mm | PLC 1 | UL 746 | |
0.75 mm | PLC 0 | UL 746 | |
1.5 mm | PLC 0 | UL 746 | |
3.0 mm | PLC 0 | UL 746 |
Flammability | Nominal Value | Unit | Test Method |
---|---|---|---|
Flame Rating 4(0.40 mm, ALL) | V-0 | UL 94 | |
Glow Wire Ignition Temperature | IEC 60695-2-13 | ||
0.40 mm | 775 | °C | IEC 60695-2-13 |
0.75 mm | 800 | °C | IEC 60695-2-13 |
1.5 mm | 825 | °C | IEC 60695-2-13 |
3.0 mm | 850 | °C | IEC 60695-2-13 |
Oxygen Index | 37 | % | ISO 4589-2 |
Injection | Nominal Value | Unit | |
---|---|---|---|
Drying Temperature | 100 | °C | |
Drying Time | 1.0 - 3.0 | hr | |
Rear Temperature | 250 - 260 | °C | |
Front Temperature | 260 - 290 | °C | |
Processing (Melt) Temp | 280 | °C | |
Mold Temperature | 120 - 140 | °C |
Injection instructions |
---|
热流道系统:250 °C~260 °C ( 482°F~500 °F ) 射出压力:快速 干燥: 该树脂应该干燥~要求的0.10% 含湿率。 如果使用的除湿空气干燥机露点为-28 ° C( -18 °F )或更低,应遵循以下规则:120 ° C(248 °F)温度下 1〜2小时, 100℃ C( 212°F)温度下2〜4小时,或80 ℃(176 °F)温度下2-8小时。 注塑成型: IXEF1524混合物在大多数螺杆注塑机上均可以很容易地注射成型。建议采用通用螺杆,背压尽可能低。 测得的熔融温度应该在270℃ (518° F)左右,机筒后端温度应该在250~260℃ ( 482~500°F )左右,前端逐渐增至260 ℃〜275℃ (500~527 °F)。如果使用热流道,温度应设置为250~260 ℃(482~500 ° F ) 。 为了最大限度地提高结晶度,模腔表面温度必须保持在120~140℃( 248~284°F)之间。成型温度低,容易使产品产生翘曲、外观不良,并极可能产生蠕变。射出压力应确保快速射出。调整保压压力和时间,尽量提高零件的重量。部件正好完全填充完毕( 95-99%)前,将注塑件从射出部位转移到螺杆位置进行保压。 |
Note Message | |
---|---|
1 . | DMS 1510/14 CFR 25.853 Appendix F Part 1, (a), 1, (i) |
2 . | Method B |
3 . | Method B |
4 . | These flammability ratings are not intended to reflect hazards presented by these or any other materials under actual fire conditions. |
Resin Grade | Manufacturer | Category | Trademark |
---|---|---|---|
Braskem PE GM5010T2 | Braskem | HDPE | Braskem PE |
BUP 612 | Bonyan Kala Chemie Company | Polyester, TS | BUP |
Formolene® E924F | Formosa Plastics Corporation, U.S.A. | HDPE, HMW | Formolene® |
Elexar® EL-3954-50 | Teknor Apex Company | TPE | Elexar® |
ROTOLENE® High Flow | Polimeros Mexicanos S.A. de C.V. | LMDPE | ROTOLENE® |