Order Products : sales@su-jiao.com
Escorene™ Ultra FL 00728CC
| Category: | EVA , Ethylene Vinyl Acetate Copolymer Resin |
| Manufacturer: | ExxonMobil Chemical |
| Trademark: | Escorene™ Ultra |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | zCw0MD_Escorene-Ultra-FL-00728CC.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| FL 00728CC is a good co-extrusion component in extrusion coating, blown film and casting film. It can be well bonded to stretched polypropylene in co-extrusion. This brand has good optical properties, low crystal point and extremely low sealing temperature when used for heat sealing. Good extrusion coating effect can be obtained at 200°C (392 °F) under processing conditions. Processing temperatures above 220°C (428 °F) may cause resin degradation. FL00728CC should be put into the extruder after low density polyethylene with similar or higher melt index. The machine should be thoroughly cleaned with low density polyethylene or suitable detergent before stopping. |
| General Information | |
|---|---|
| Additive |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Vinyl Acetate Content | 27.5 | wt% | ExxonMobil Method |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 15 sec) | 80 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus 1 | 17.0 | MPa | ASTM D638 |
| Tensile Elongation 2(Break) | > 100 | % | ASTM D638 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Vicat Softening Temperature | 43.0 | °C | ASTM D1525 |
| Legal statement |
|---|
| 本产品不宜在医疗应用中使用，亦不应在任何此类应用中使用有关潜在食品接触应用合规信息（例如：FDA、EU、HPFB），请与埃克森美孚化工客户服务代表联系。 |
| Extrusion instructions |
|---|
| Excellent results are obtained in extrusion coating at 200°C (392°F) temperature range. Processing temperatures above 220°C (428°F) may cause resin degradation. FL00728CC should be fed into the extruder after LDPE of a similar or higher melt index. Machines should always be purged with LDPE or a suitable cleaning compound before shutdown. |
| Note Message | |
|---|---|
| 1 . | 5.0 mm/min |
| 2 . | 500 mm/min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| SCLAIR® FP120 Series | NOVA Chemicals | LLDPE | SCLAIR® |
| Fainplast PVC CKL 76/V | Fainplast Compounds S.r.l | PVC, Unspecified | Fainplast PVC |
| Epolene® E-25 | Westlake Chemical Corporation | PP, Unspecified | Epolene® |
| PLUSTEK PA303G33 | Polyram Ram-On Industries | Nylon 66 | PLUSTEK |
| LNP™ LUBRICOMP™ DL0049EF compound | SABIC Innovative Plastics | PC | LNP™ LUBRICOMP™ |
