Order Products : sales@su-jiao.com
Generic TPV
| Category: | TPV , Thermoplastic Vulcanizate |
| Manufacturer: | Generic |
| Trademark: | Generic |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | zAvegb_Generic-TPV.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
This data represents typical values that have been calculated from all products classified as: Generic TPV This information is provided for comparative purposes only. |
| General Information |
|---|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | |||
| -- | 0.879 - 0.999 | g/cm³ | ASTM D792 |
| 23°C | 0.901 - 0.983 | g/cm³ | ISO 1183 |
| -- | 0.879 - 0.893 | g/cm³ | ASTM D1505 |
| Melt Mass-Flow Rate (MFR) | |||
| 230°C/2.16 kg | 0.54 - 2.5 | g/10 min | ASTM D1238 |
| 190°C/5.0 kg | 2.0 - 6.2 | g/10 min | ISO 1133 |
| Molding Shrinkage | ASTM D955 | ||
| Flow : 23°C | 1.3 - 3.0 | % | ASTM D955 |
| Transverse flow : 23°C | 0.97 - 1.6 | % | ASTM D955 |
| Detergent Resistance | f4 | UL 2157 | |
| Detergent Resistance | f3 | UL 749 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (23°C) | 45 - 90 | ASTM D785 | |
| Durometer Hardness | |||
| 23°C | 28 - 95 | ASTM D2240 | |
| 23°C | 34 - 93 | ISO 868 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength | |||
| Yield, 23°C | 4.48 - 110 | MPa | ASTM D638 |
| Fracture, 23°C | 3.00 - 22.0 | MPa | ISO 527-2 |
| 23°C | 1.00 - 13.5 | MPa | ASTM D638 |
| 23°C | 4.10 - 8.40 | MPa | ISO 527-2 |
| Tensile Elongation | |||
| Fracture, 23°C | 300 - 710 | % | ASTM D638 |
| Fracture, 23°C | 440 - 610 | % | ISO 527-2 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Set (23°C) | 6 - 33 | % | ASTM D412 |
| Tensile Stress | |||
| 50% strain, 23°C | 0.965 - 3.01 | MPa | ASTM D412 |
| 100% strain, 23°C | 0.500 - 4.82 | MPa | ASTM D412 |
| 100% strain, 23°C | 0.995 - 5.92 | MPa | ISO 37 |
| 300% strain, 23°C | 1.11 - 9.76 | MPa | ASTM D412 |
| 300% strain, 23°C | 2.07 - 10.3 | MPa | ISO 37 |
| Tensile Strength | |||
| Yield, 23°C | 1.38 - 17.3 | MPa | ASTM D412 |
| Yield, 23°C | 2.94 - 22.2 | MPa | ISO 37 |
| Fracture, 23°C | 2.33 - 12.1 | MPa | ASTM D412 |
| Fracture, 23°C | 2.05 - 18.0 | MPa | ISO 37 |
| Tensile Elongation | |||
| Yield | 300 - 700 | % | ASTM D412 |
| Fracture, 23°C | 280 - 680 | % | ASTM D412 |
| Fracture, 23°C | 330 - 700 | % | ISO 37 |
| Tear Strength | |||
| 23°C | 7.21 - 51.7 | kN/m | ASTM D624 |
| 23°C | 11 - 55 | kN/m | ISO 34-1 |
| Compression Set | |||
| -- | 15 - 63 | % | ASTM D395 |
| 23°C | 9.2 - 37 | % | ISO 815 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength in Air (23°C) | -61 - -0.20 | % | ASTM D573, ISO 188 |
| Change in Ultimate Elongation in Air (23°C) | -70 - 26 | % | ASTM D573, ISO 188 |
| Change in Durometer Hardness in Air (23°C) | -4.0 - 8.0 | ASTM D573, ISO 188 | |
| Change in Tensile Strength (23°C) | -32 - 31 | % | ASTM D471, ISO 1817 |
| Change in Ultimate Elongation (23°C) | -50 - 25 | % | ASTM D471, ISO 1817 |
| Change in Durometer Hardness (23°C) | -3.0 - 3.0 | ASTM D471, ISO 1817 | |
| Change in Mass (23°C) | -1.7 - 2.2 | % | ASTM D471 |
| Change in Mass (22.8°C) | -1.7 - 2.2 | % | ISO 1817 |
| Change in Volume | |||
| 23°C | 0.0 - 1.2 | % | ASTM D471 |
| 23°C | 0.0 - 0.70 | % | ISO 1817 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Continuous Use Temperature | 125 - 140 | °C | ASTM D794 |
| Brittleness Temperature | |||
| -- | -60.6 - -59.5 | °C | ASTM D746 |
| -- | -60.4 - -55.8 | °C | ISO 812 |
| Melting Temperature | 158 - 160 | °C | |
| RTI Elec | 50.0 - 100 | °C | UL 746 |
| RTI Imp | 50.0 - 65.0 | °C | UL 746 |
| RTI | 50.0 - 95.0 | °C | UL 746 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity (23°C) | 1.0E+3 - 2.8E+16 | ohms·cm | ASTM D257 |
| Dielectric Strength (23°C) | 12 - 32 | kV/mm | ASTM D149 |
| Dielectric Constant | |||
| 23°C | 2.29 - 2.70 | ASTM D150 | |
| 23°C | 2.30 - 2.70 | IEC 60250 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Burning Rate | 15 - 32 | mm/min | ISO 3795 |
| Oxygen Index | 24 - 27 | % | ASTM D2863 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 69.4 - 90.0 | °C | |
| Drying Time | 2.0 - 3.0 | hr | |
| Suggested Max Moisture | 0.080 - 0.083 | % | |
| Rear Temperature | 142 - 201 | °C | |
| Middle Temperature | 162 - 205 | °C | |
| Front Temperature | 179 - 206 | °C | |
| Nozzle Temperature | 195 - 211 | °C | |
| Processing (Melt) Temp | 196 - 217 | °C | |
| Mold Temperature | 29.3 - 47.8 | °C | |
| Injection Pressure | 4.14 - 104 | MPa | |
| Back Pressure | 0.0400 - 0.663 | MPa | |
| Screw Speed | 73 - 150 | rpm | |
| Clamp Tonnage | 5.5 | kN/cm² | |
| Cushion | 4.76 - 14.6 | mm |
| Injection instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic TPVThis information is provided for comparative purposes only. |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 78.9 - 90.0 | °C | |
| Drying Time | 1.8 - 3.0 | hr | |
| Hopper Temperature | 168 - 171 | °C | |
| Cylinder Zone 1 Temp. | 160 - 191 | °C | |
| Cylinder Zone 2 Temp. | 170 - 193 | °C | |
| Cylinder Zone 3 Temp. | 174 - 197 | °C | |
| Cylinder Zone 4 Temp. | 180 - 199 | °C | |
| Cylinder Zone 5 Temp. | 181 - 206 | °C | |
| Adapter Temperature | 200 - 201 | °C | |
| Melt Temperature | 194 - 205 | °C | |
| Die Temperature | 170 - 210 | °C | |
| Back Pressure | 12.5 | MPa |
| Extrusion instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic TPVThis information is provided for comparative purposes only. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RIALFLAME H V2L 15 H 20 TD | RIALTI Srl | PP Homopolymer | RIALFLAME |
| NITRIFLEX NP-6021 | NITRIFLEX | NBR | NITRIFLEX |
| Durez® 4400 | Sumitomo Bakelite North America, Inc. | Phenolic | Durez® |
| KumhoSunny PBT 3730FG | Shanghai KumhoSunny Plastics Co., Ltd. | PBT | KumhoSunny PBT |
| Daelim Po1y® XP9500 | DAELIM INDUSTRIAL CO., LTD. | mLLDPE | Daelim Po1y® |
