Order Products : sales@su-jiao.com
AXELERON™ CX 1253 NT CPD
| Category: | LDPE , Low Density Polyethylene Insulation Compound |
| Manufacturer: | The Dow Chemical Company |
| Trademark: | AXELERON™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | xKfNMx_AXELERON-CX-1253-NT-CPD.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Low density insulating material AXELERON™CX A- 1253 NT is a medium-molecular-weight, low-density polyethylene insulating resin, which is used in a variety of applications that require strict electrical properties. DFDA-1253 Natural can be used as a part of resin in the gas injection process for the preparation of foam insulation materials for coaxial cables. Specifications AXELERON™CX A- 1253 NT meets the following raw material specifications:
|
| General Information | |
|---|---|
| Uses |
|
| Agency Ratings |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.919 | g/cm³ | ASTM D1505 |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 1.8 | g/10 min | ASTM D1238 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength | 11.4 | MPa | ASTM D638 |
| Tensile Elongation (Break) | 600 | % | ASTM D638 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | > 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric Strength 1(3.18 mm) | 22 | kV/mm | ASTM D149 |
| Dielectric Constant (1 MHz) | 2.27 | ASTM D1531 | |
| Dissipation Factor (1 MHz) | 7.0E-5 | ASTM D1531 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Melt Temperature | 190 - 220 | °C |
| Extrusion instructions |
|---|
| AXELERON™ CX 1253 NT CPD provides excellent surface finish and outstanding output rates over a broad range of conditions. For optimum results, use melt extrusion temperatures in the suggested range of 375 to 425°F (190 to 220°C). However, specific recommendations for processing conditions can be determined only when the application and type of processing equipment are known. |
| Note Message | |
|---|---|
| 1 . | Method A (short time) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| ProPell™ TPU 55D 0118A | Foster Corporation | Unspecified | ProPell™ |
| DJSilicone NE--T-2/NE-T-2U (standard) | DONGJUE SILICONE (NANJING) CO., LTD | Silicone | DJSilicone |
| KEP® 570P | Kumho Polychem Co., Ltd. | EPDM | KEP® |
| LNP™ THERMOCOMP™ WX93111 compound | SABIC Innovative Plastics Europe | PBT | LNP™ THERMOCOMP™ |
| Perfactory® RC25 | EnvisionTEC, Inc. | Unspecified | Perfactory® |
