TECHNYL eXten® D 219WFC V30 BLACK Datasheet,Nylon 610,Solvay Engineering Plastics-SHANGHAI SUSHENG

Message
TECHNYL eXten® D 219WFC V30 Black is a polyamide 6.10, reinforced with 30% of glass fibre, heat stabilized with organic stabilizers, for injection moulding. This grade offers lower water uptake, higher dimensional stability and enhanced chlorine resistance versus standard PA 6.6. It offers too an enhanced corrosion resistance, a reduction in lead levels versus standard metal solutions and an increase in ease of processing and part design freedom versus metal solutions and other plastics. It is used for cold and warm water plumbing components including, but not limited to, components in contact with drinking water systems globally where elevated levels of chlorine could be present.

General Information
Filler / Reinforcement	Glass fiber reinforced material, 30% filler by weight
Additive	heat stabilizer
Features	Drinking Water Contact Acceptable Heat Stabilized - Organic Good dimensional stability Updatable resources Good chemical resistance Compliance of Food Exposure
Uses	Pump parts Valve/valve components Industrial application Consumer goods application field
Agency Ratings	ACS DGSNS4 No. 2000/232 DVGW W270 EC 1907/2006 (REACH) KTW Guidelines NSF 61 NSF Not Rated WRAS BS6920-1: 2000 and 2014
RoHS Compliance	RoHS compliance
Appearance	Black
Forms	Particle
Processing Method	Injection molding
Resin ID (ISO 1043)	PA610-GF30

Physical	Nominal Value	Unit	Test Method
Density	1.31	g/cm³	ISO 1183/A
Water Absorption			ISO 62
23°C, 24 hr	0.36	%	ISO 62
Saturated, 23°C	2.4	%	ISO 62

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (23°C)	9200	MPa	ISO 527-2/1A
Tensile Stress (Break, 23°C)	150	MPa	ISO 527-2/1A
Tensile Strain (Break, 23°C)	4.1	%	ISO 527-2
Flexural Modulus
23°C	7200	MPa	ASTM D790
23°C	7700	MPa	ISO 178
Flexural Strength
23°C	235	MPa	ASTM D790
23°C	250	MPa	ISO 178

Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (23°C)	11	kJ/m²	ISO 179/1eA
Notched Izod Impact (23°C)	12	kJ/m²	ISO 180

Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature (1.8 MPa, Unannealed)	203	°C	ISO 75-2/Af
Melting Temperature	225	°C	ISO 11357-3

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	2.9E+15	ohms	IEC 60093
Volume Resistivity	3.9E+15	ohms·cm	IEC 60093
Dielectric Strength (2.00 mm)	27	kV/mm	IEC 60243-1
Relative Permittivity	3.40		IEC 60250
Comparative Tracking Index (Solution A)	600	V	IEC 60112

Flammability	Nominal Value	Unit	Test Method
Flame Rating			UL 94
1.6 mm	HB		UL 94
3.2 mm	HB		UL 94
Glow Wire Flammability Index (1.6 mm)	700	°C	IEC 60695-2-12

Injection	Nominal Value	Unit
Drying Temperature	80	°C
Suggested Max Moisture	0.20	%
Rear Temperature	265 - 275	°C
Middle Temperature	270 - 280	°C
Front Temperature	275 - 285	°C
Mold Temperature	70 - 100	°C

Injection instructions
The material is supplied in airtight bags, ready for use. In case that the virgin material has absorbed moisture, it must be dried with a dehumidified air drying equipment, dew point mini -20°C. Recommended time 2-4hInjection Advice: For reinforced polyamide, Solvay recommends the use of steel with a high content of Carbon and purified for polishing to avoid or limit the abrasion. For example: X38CrMoV5-1 (EN Norm) - 1.2367 /1.2343 (DIN Norm) or X160CrMoV12 (EN Norm) - 1.2601 /1.2379 (DIN Norm). For Mould Temperature, in the case of parts where the surface roughness is required we can recommend a temperature of 90°C to 120°C with an optimum at 105°C. The processing parameters like processing temperatures are a recommendation and can be adjusted in function of injection machine size, part geometry / design

Injection instructions

The material is supplied in airtight bags, ready for use. In case that the virgin material has absorbed moisture, it must be dried with a dehumidified air drying equipment, dew point mini -20°C. Recommended time 2-4hInjection Advice: For reinforced polyamide, Solvay recommends the use of steel with a high content of Carbon and purified for polishing to avoid or limit the abrasion. For example: X38CrMoV5-1 (EN Norm) - 1.2367 /1.2343 (DIN Norm) or X160CrMoV12 (EN Norm) - 1.2601 /1.2379 (DIN Norm). For Mould Temperature, in the case of parts where the surface roughness is required we can recommend a temperature of 90°C to 120°C with an optimum at 105°C. The processing parameters like processing temperatures are a recommendation and can be adjusted in function of injection machine size, part geometry / design

Category:	Nylon 610 , Polyamide 610
Manufacturer:	Solvay Engineering Plastics
Trademark:	TECHNYL eXten®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	waGgLc_TECHNYLeXtenD219WFCV30BLACK.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Sinelec CCB6005	Teknor Apex Asia Pacific PTE. LTD.	PS (Specialty)	Sinelec
Chemlon® 66AH	Teknor Apex Company (Chem Polymer)	Nylon 66	Chemlon®
ICORENE® N7020	ICO Polymers EMEA, A Division of A. Schulman	LDPE	ICORENE®
INSULCAST® 3230 LV/INSULCURE 9	ITW Polymers Coatings North America	Epoxy	INSULCAST®
SD POLYCA™ LD2050-AAH14	Sumika Styron Polycarbonate Limited	PC	SD POLYCA™