Versollan™ OM 1262NX-9 Datasheet,TPE,PolyOne Corporation-SHANGHAI SUSHENG

Message
Versollan™OM 1262NX-9 is a high-performance polyurethane (TPU) alloy designed for thin-walled overlapping molding with polycarbonate (PC), ABS, PC/ABS and copolyester substrates. Matte, imitation rubber surface is easier to grasp tested by practice Excellent adhesion to PC, ABS, PC/ABS, PC/PBT and copolyester

General Information
Features	Gloss, low Workability, good Good formability
Uses	overmolding Thin wall parts Electrical/Electronic Applications Power/other tools Soft handle Business equipment Consumer goods application field
Agency Ratings	UL 94 .QMFZ2.E76261
RoHS Compliance	RoHS compliance
Appearance	Black
Forms	Particle
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.17	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR)			ASTM D1238
190°C/2.16 kg	7.0	g/10 min	ASTM D1238
200°C/5.0 kg	100	g/10 min	ASTM D1238
Molding Shrinkage - Flow	0.90 - 1.5	%	ASTM D955

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A, 10 sec)	65		ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress ¹			ASTM D412
100% strain, 23°C ²	2.55	MPa	ASTM D412
300% strain, 23°C ³	3.34	MPa	ASTM D412
Tensile Strength (Break, 23°C)	7.64	MPa	ASTM D412
Tensile Elongation (Break, 23°C)	710	%	ASTM D412
Tear Strength	40.3	kN/m	ASTM D624
Compression Set (23°C, 22 hr)	35	%	ASTM D395B

Flammability	Nominal Value		Test Method
Flame Rating (1.50 mm)	HB		UL 94

Fill Analysis	Nominal Value	Unit	Test Method
Apparent Viscosity (200°C, 11200 sec^-1)	19.9	Pa·s	ASTM D3835

Injection	Nominal Value	Unit
Drying Temperature	51.7 - 54.4	°C
Drying Time	3.0 - 4.0	hr
Suggested Max Moisture	< 0.030	%
Suggested Max Regrind	20	%
Rear Temperature	163 - 185	°C
Middle Temperature	168 - 196	°C
Front Temperature	177 - 210	°C
Nozzle Temperature	177 - 210	°C
Mold Temperature	21.1 - 48.9	°C
Back Pressure	0.172 - 0.345	MPa
Screw Speed	25 - 75	rpm

Injection instructions
在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Versollan™ OM 1262NX-9 可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Versollan™ OM 1262NX-9 不应在机筒内闲置过长时间（5 分钟以上）。建议露点：-40°F注射速度：1 - 5 英寸/秒第一阶段 - 提升压力：200 - 800 psi第二阶段 - 保持压力：70% 的升压保持时间（厚部件）：4 - 10 秒保持时间（薄部件）：1 - 3 秒

Injection instructions

在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Versollan™ OM 1262NX-9 可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Versollan™ OM 1262NX-9 不应在机筒内闲置过长时间（5 分钟以上）。建议露点：-40°F注射速度：1 - 5 英寸/秒第一阶段 - 提升压力：200 - 800 psi第二阶段 - 保持压力：70% 的升压保持时间（厚部件）：4 - 10 秒保持时间（薄部件）：1 - 3 秒

Note Message
1 .	2 hours
2 .	Mouth die c
3 .	C mould

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	PolyOne Corporation
Trademark:	Versollan™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	wG8zEs_Versollan-OM-1262NX-9.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Sindustris PP HI5205S	Sincerity Australia Pty Ltd.	PP, Unspecified	Sindustris PP
ExxonMobil™ PP7905E1	ExxonMobil Chemical	PP Impact Copolymer	ExxonMobil™
Gallonprene® GP420-4503	Shenzhen Sungallon Rubber & Plastic Corporation Limited	TPE	Gallonprene®
EMPILON® 555	EMPILON	SEBS	EMPILON®
INEOS PP 401-CA55	INEOS Olefins & Polymers Europe	PP Impact Copolymer	INEOS PP