Order Products : sales@su-jiao.com
SABIC® LLDPE R50035EE
| Category: | LLDPE , Linear Low Density Polyethylene |
| Manufacturer: | Saudi Basic Industries Corporation (SABIC) |
| Trademark: | SABIC® LLDPE |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | vdZxYX_SABIC-LLDPE-R50035EE.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
SABIC® LLDPE R50035EE is a LLDPE copolymer that typically provides good stress crack resistance, rigidity, toughness, gloss and very low warpage. The resin contains UV stabilizer. It is recommended that SABIC® LLDPE R50035EE is grinded before use in rotational moulding applications. Typical Applications. SABIC® LLDPE R50035EE is typically used for rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Because of its good mechanical properties and low warpage, it is typically used for injection moulding of screw closures, caps and housewares. SABIC® LLDPE R50035EE is UV stabilised; which provides good protection for the final product. This product is not intended for and must not be used in any pharmaceutical/medical applications. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.933 | g/cm³ | ASTM D1505 |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 5.0 | g/10 min | ASTM D1238 |
| Environmental Stress-Cracking Resistance (100% Igepal CO-630, Compression Molded, F50) | > 150 | hr | ASTM D1693B |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore D, Compression Molded) | 66 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength | ASTM D638 | ||
| Yield, Compression Molded | 16.0 | MPa | |
| Break, Compression Molded | 17.0 | MPa | |
| Tensile Elongation (Break, Compression Molded) | 590 | % | ASTM D638 |
| Flexural Modulus - 1% Secant (Compression Molded) | 420 | MPa | ASTM D790 |
| Flexural Strength (Compression Molded) | 13.0 | MPa | ASTM D790 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | < -75.0 | °C | ASTM D746 |
| Vicat Softening Temperature | 114 | °C | ASTM D1525 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 210 to 240 | °C |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| PRE-ELEC® ABS 1415 | Premix Oy | ABS | PRE-ELEC® |
| VAMPAMID HT 0023 V0 | Vamp Tech | PPA | VAMPAMID |
| DOW™ HDPE DMDA-8907 NT 7 | The Dow Chemical Company | HDPE | DOW™ HDPE |
| Dryflex® 402901S | ELASTO | SBS | Dryflex® |
| Eltex® Superstress™ TUB124N6000 | INEOS Olefins & Polymers Europe | HDPE Copolymer | Eltex® |
