Order Products : sales@su-jiao.com
Bergaflex™ BFI 45A-300
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | Bergaflex™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | uNUWeK_Bergaflex-BFI-45A-300.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| Bergaflex thermoplastic elastomer polymer is mixed with hydrogenated styrene block copolymer. In addition to having OnFlex™The main characteristics of-S products, such as high hardness, good mechanical properties, good processability, good coloring properties, and a large operating temperature range, this series of polymers has excellent cost performance. OnFlex™-S EH polymer is filled with other substances, so it is opaque and has a relatively high density. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.17 | g/cm³ | ISO 1183 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 45 | ISO 868 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (Break) | 5.00 | MPa | ISO 37 |
| Tensile Elongation (Break) | 720 | % | ISO 37 |
| Compression Set | ISO 815 | ||
| 23°C, 72 hr | 15 | % | ISO 815 |
| 70°C, 22 hr | 50 | % | ISO 815 |
| Additional Information | Nominal Value | ||
|---|---|---|---|
| General Material Type | Styrene thermoplastic elastomers (TES) | ||
| 各项属性值是采用注射模制基板测量得出。 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 180 - 220 | °C | |
| Mold Temperature | 30.0 - 60.0 | °C | |
| Injection Rate | Fast |
| Injection instructions |
|---|
| Purge thoroughly before and after use of this product with a low flow (0.5 - 2.5 MFR) polyethylene (PE) or polypopylene (PP).BFI 45A-300 has excellent melt stability. Maximum residence times may vary, depending on the size of the barrel. Generally, the barrel should be emptied if it is idle for periods of 8 - 10 minutes or longer.Drying is not RequiredInjection Speed: 1 to 3 in/sec1st Stage - Boost Pressure: 200 to 900 psi2nd Stage - Hold Pressure: 50% of BoostHold Time (Thick Part): 3 to 10 secHold Time (Thin Part): 1 to 3 sec |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Manner Flexible PVC X4775 | Manner Plastics, L.P. | PVC, Flexible | Manner Flexible PVC |
| Wellamid® 22LH-WBK | Wellman Engineering Resins | Nylon 66 | Wellamid® |
| Network Polymers LDPE 10 0218 | Network Polymers, Inc. | EVA | Network Polymers LDPE |
| Jiangsu Meilan XXMLF2-10 | Jiangsu Meilan Chemical Co., Ltd. | Fluorelastomer | Jiangsu Meilan |
| LNP™ STAT-KON™ PFD06 compound | SABIC Innovative Plastics | Nylon 6 | LNP™ STAT-KON™ |
