Order Products : sales@su-jiao.com
Generic MPR
| Category: | MPR , Melt Processable Rubber |
| Manufacturer: | Generic |
| Trademark: | Generic |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | tS7a0q_Generic-MPR.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
This data represents typical values that have been calculated from all products classified as: Generic MPR This information is provided for comparative purposes only. |
| General Information |
|---|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | |||
| -- | 1.08 - 1.31 | g/cm³ | ASTM D792 |
| 23°C | 1.06 - 1.31 | g/cm³ | ISO 1183 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness | |||
| 23°C | 56 - 79 | ASTM D2240 | |
| 23°C | 57 - 79 | ISO 868 | |
| IRHD Hardness | 47 - 93 | ISO 48 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus (23°C) | 1.93 - 8.48 | MPa | ASTM D638, ISO 527-2 |
| Tensile Strength | |||
| Yield, 23°C | 4.81 - 13.1 | MPa | ASTM D638 |
| Yield, 23°C | 6.89 - 13.1 | MPa | ISO 527-2 |
| Tensile Elongation | |||
| Fracture, 23°C | 300 - 670 | % | ASTM D638 |
| Fracture, 23°C | 300 - 470 | % | ISO 527-2 |
| Taber Abrasion Resistance (23°C) | 0.00100 - 9.00 | mg | ASTM D1044 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Set (23°C) | 6 - 13 | % | ASTM D412 |
| Tensile Stress | |||
| 100% strain, 23°C | 2.28 - 6.05 | MPa | ASTM D412 |
| 100% strain, 23°C | 2.50 - 5.95 | MPa | ISO 37 |
| Tensile Strength | |||
| Yield, 23°C | 6.49 - 11.9 | MPa | ASTM D412 |
| Yield, 23°C | 7.85 - 11.2 | MPa | ISO 37 |
| Tensile Elongation | |||
| Fracture, 23°C | 300 - 680 | % | ASTM D412 |
| Fracture, 23°C | 320 - 630 | % | ISO 37 |
| Tear Strength (23°C) | 19.2 - 62.5 | kN/m | ASTM D624 |
| Compression Set | |||
| -- | 12 - 89 | % | ASTM D395 |
| 23°C | 12 - 27 | % | ISO 815 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Volume (23°C) | 8.0 - 43 | % | ASTM D471 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | |||
| -- | -91.1 - -52.2 | °C | ASTM D746 |
| -- | -91.0 - -52.2 | °C | ISO 812 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melt Viscosity | 115 - 870 | Pa·s | ASTM D3835 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 166 - 177 | °C |
| Injection instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic MPRThis information is provided for comparative purposes only. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Rigidex® HM5060XA | INEOS Olefins & Polymers Europe | HDPE, HMW | Rigidex® |
| Rhelon G3533H-01 | RheTech, Inc. | Nylon 66/6 | Rhelon |
| Varcum 29111 | Durez Corporation | Phenolic | Varcum |
| Echo® RPEHD NAT | Ravago Manufacturing Americas, LLC | HDPE | Echo® |
| Vipel® F737-BCF-00 | AOC, L.L.C. | Polyester Alloy | Vipel® |
