Durethan® BKV 15 000000 Datasheet,Nylon 6,LANXESS GmbH-SHANGHAI SUSHENG

Message
PA 6-Copolymer, 15 % glass fibers, injection molding

General Information
Filler / Reinforcement	Glass Fiber, 15% Filler by Weight
Features	Copolymer
Processing Method	Injection Molding
Multi-Point Data	Creep Modulus vs. Time (ISO 11403-1) Isochronous Stress vs. Strain (ISO 11403-1) Isothermal Stress vs. Strain (ISO 11403-1) Secant Modulus vs. Strain (ISO 11403-1) Shear Modulus vs. Temperature (ISO 11403-1) Viscosity vs. Shear Rate (ISO 11403-2)

Physical	Dry	Conditioned	Unit	Test Method
Specific Gravity
--	1.22 1.23	--	g/cm³	ASTM D792
23°C	1.23	--	g/cm³	ISO 1183
Apparent Density	0.70	--	g/cm³	ISO 60
Molding Shrinkage				ISO 2577
Across Flow : 280°C, 3.00 mm ¹	0.88	--	%
Across Flow : 120°C, 4 hr, 3.00 mm ²	0.21	--	%
Flow : 280°C, 3.00 mm ³	0.29	--	%
Flow : 120°C, 4 hr, 3.00 mm ⁴	0.080	--	%
Water Absorption				ISO 62
Saturation, 23°C	8.5	--	%
Equilibrium, 23°C, 50% RH	2.6	--	%

Hardness	Dry	Conditioned	Unit	Test Method
Ball Indentation Hardness	170	80.0	MPa	ISO 2039-1

Mechanical	Dry	Conditioned	Unit	Test Method
Tensile Modulus
23°C ⁵	6200	3100	MPa	ASTM D638
23°C	6000	3000	MPa	ISO 527-2/1
Tensile Strength
Break, 23°C	130	70.3	MPa	ASTM D638
Break, 23°C	125	75.0	MPa	ISO 527-2/5
Tensile Elongation
Break, 23°C	3.0	5.0	%	ASTM D638
Break, 23°C	3.0	12	%	ISO 527-2/5
Flexural Modulus
23°C	5400	2900	MPa	ASTM D790
23°C ⁶	5200	3100	MPa	ISO 178/A
Flexural Strength
23°C	200	120	MPa	ASTM D790
3.5% Strain, 23°C	180	90.0	MPa	ISO 178/A
23°C ⁷	200	120	MPa	ISO 178/A
Flexural Strain at Flexural Strength ⁸(23°C)	5.0	8.0	%	ISO 178/A

Additional Information	Dry	Conditioned		Test Method
ISO Shortname	PA 6/66, GR, 14-060, GF15	--		ISO 1874

Injection	Dry	Unit	Test Method
Residual Moisture Content	0.030 to 0.12	%	Karl Fisher

Impact	Dry	Conditioned	Unit	Test Method
Charpy Notched Impact Strength				ISO 179/1eA
-40°C	< 10	< 10	kJ/m²
-30°C	< 10	< 10	kJ/m²
23°C	< 10	10	kJ/m²
Charpy Unnotched Impact Strength				ISO 179/1eU
-30°C	35	35	kJ/m²
23°C	45	70	kJ/m²
Notched Izod Impact
-40°C, 3.18 mm	53	53	J/m	ASTM D256
23°C, 3.18 mm	64	250	J/m	ASTM D256
-40°C	< 10	< 10	kJ/m²	ISO 180/1A
-30°C	< 10	< 10	kJ/m²	ISO 180/1A
Unnotched Izod Impact Strength				ISO 180/1U
-30°C	30	30	kJ/m²
23°C	30	80	kJ/m²
Multi-Axial Instrumented Impact Energy				ISO 6603-2
-30°C	3.00	--	J
23°C	4.00	--	J
Multi-Axial Instrumented Impact Peak Force				ISO 6603-2
-30°C	585	--	N
23°C	644	--	N

Thermal	Dry	Conditioned	Unit	Test Method
Deflection Temperature Under Load
0.45 MPa, Unannealed, 39.9 mm	215	--	°C	ASTM D648
0.45 MPa, Unannealed	210	--	°C	ISO 75-2/B
1.8 MPa, Unannealed	190	--	°C	ISO 75-2/A
1.8 MPa, Annealed, 3.99 mm	200	--	°C	ASTM D648
8.0 MPa, Unannealed	60.0	--	°C	ISO 75-2/C
Vicat Softening Temperature
--	200	--	°C	ISO 306/B50
--	> 200	--	°C	ISO 306/B120
Melting Temperature ⁹	213	--	°C	ISO 11357-3
CLTE				ISO 11359-2
Flow : 23 to 55°C	3.0E-5	--	cm/cm/°C
Transverse : 23 to 55°C	8.0E-5	--	cm/cm/°C

Electrical	Dry	Conditioned	Unit	Test Method
Surface Resistivity	1.0E+13 to 1.0E+14	1.0E+12	ohms	IEC 60093
Volume Resistivity (23°C)	1.0E+15	1.0E+12	ohms·cm	IEC 60093
Electric Strength				IEC 60243-1
23°C, 1.00 mm	40	35	kV/mm
23°C, 3.00 mm	35	31	kV/mm
Dielectric Constant
23°C, 50 Hz ¹⁰	4.00	15.0		IEC 60250
23°C, 1 MHz ¹¹	4.00	5.00		IEC 60250
23°C, 100 Hz	4.00	10.0		IEC 60250
Dissipation Factor				IEC 60250
23°C, 50 Hz	5.0E-3	0.50
23°C, 100 Hz	5.0E-3	0.20
23°C, 1 MHz	0.015 0.015	0.12 0.16
Comparative Tracking Index
Solution A	600	--	V	IEC 60112
Solution B	425	--	V	IEC 60112
--	--	425	V	ASTM D3638

Flammability	Dry	Conditioned	Unit	Test Method
Burning Rate ¹²(1.00 mm)	< 60	--	mm/min	ISO 3795
Flame Rating				UL 94
1.60 mm	HB	--
3.20 mm	HB	--
Glow Wire Flammability Index (2.00 mm)	650	--	°C	IEC 60695-2-12
Oxygen Index ¹³	22	--	%	ISO 4589-2

Injection	Dry	Unit
Drying Temperature - Dry Air Dryer	80.0	°C
Drying Time - Dry Air Dryer	2.0 to 6.0	hr
Processing (Melt) Temp	260 to 290	°C
Mold Temperature	80.0 to 100	°C

Category:	Nylon 6 , Polyamide 6
Manufacturer:	LANXESS GmbH
Trademark:	Durethan®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	sm1uyG_Durethan-BKV-15-000000.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Pro-fax SA861	LyondellBasell Industries	PP Random Copolymer	Pro-fax
UNIFONE® PSU	Nytef Plastics, Ltd.	PSU	UNIFONE®
Varcum 29557	Durez Corporation	Phenolic	Varcum
ADDILENE J 420 K24	ADDIPLAST	PP Copolymer	ADDILENE
Lucene™ LC760	LG Chem Ltd.	TPO (POE)	Lucene™