Beetle® PBTS120CF Datasheet,PBT,Teknor Apex Company (Chem Polymer)-SHANGHAI SUSHENG

Message
PBTS120CF is a 20% carbon fibre reinforced grade of PBT that is formulated with injection moulding of components in mind. The carbon fibre loading imparts a high level of stiffness over a wide range of service environments.

General Information
Filler / Reinforcement	Carbon fiber reinforced material, 20% filler by weight
Features	Good dimensional stability Prevent continuous charging Rigidity, high
Forms	Particle
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Density	1.38	g/cm³	ISO 1183
Molding Shrinkage ¹	0.50 - 0.70	%	Internal method
Water Absorption (Equilibrium, 23°C, 50% RH)	0.10	%	ISO 62

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus	14500	MPa	ISO 527-2
Tensile Stress (Yield)	170	MPa	ISO 527-2
Tensile Strain (Break)	2.0	%	ISO 527-2
Flexural Modulus	12000	MPa	ISO 178
Flexural Stress	225	MPa	ISO 178

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact	5.0	kJ/m²	ISO 180

Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
0.45 MPa, not annealed	> 200	°C	ISO 75-2/B
1.8 MPa, not annealed	> 200	°C	ISO 75-2/A

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	1.0E+3	ohms	IEC 60093

Injection	Nominal Value	Unit
Drying Temperature	120	°C
Drying Time	4.0	hr
Rear Temperature	250 - 260	°C
Middle Temperature	250 - 270	°C
Front Temperature	250 - 270	°C
Processing (Melt) Temp	< 280	°C
Mold Temperature	60.0 - 80.0	°C
Injection Rate	Fast
Screw Speed	50 - 200	rpm

Injection instructions
Back Pressure: LowInjection Pressure: HighPolyester grades are very sensitive to moisture content during processing. Suitable pre-drying is essential. Excess moisture causes rapid hydrolytic degradation of the melt and severe impairment of mechanical properties. Low melt viscosity & brittle product are often the key indicators. Vacuum or dehumidified air driers must be used.

Note Message
1 .	Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions. The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).

Note Message

1 .

Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions. The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).

Resin Grade	Manufacturer	Category	Trademark
TECHNYL® A 205F BLACK 21 N	Solvay Engineering Plastics	Nylon 66	TECHNYL® A
Sinpolene HFR8214	Teknor Apex Asia Pacific PTE. LTD.	PP, Unspecified	Sinpolene
TAIRIPRO T8002	Formosa Plastics Corporation	PP Impact Copolymer	TAIRIPRO
Sylvin 83052-90 White 1592	Sylvin Technologies Incorporated	PVC, Unspecified	Sylvin
OTECH TPO OTR7598 - Gasket	OTECH Corporation	TPE	OTECH TPO

Category:	PBT , Polybutylene Terephthalate
Manufacturer:	Teknor Apex Company (Chem Polymer)
Trademark:	Beetle®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	nEuL7C_Beetle-PBTS120CF.pdf
PRICE:	Order Products email sales@su-jiao.com