Order Products : sales@su-jiao.com
DuraGrip® DGR 6185BK
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Advanced Polymer Alloys |
| Trademark: | DuraGrip® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | mSSS4E_DuraGrip-DGR-6185BK.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| DuraGrip® 6185BK is a black, special purpose Melt Processible Elastomer (MPE) that is easy to use in injection molding and extrusion processes. DGR 6185BK has an excellent soft touch feel and will Bond to varying Nylons, ABS, PC, PC/ABS. DuraGrip™ 6100 series is hygroscopic and requires drying prior to use. |
| General Information | |
|---|---|
| Features |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Appearance |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.14 | g/cm³ | ASTM D471, ISO 2781 |
| Molding Shrinkage | |||
| Flow : 1.59mm | 1.9 | % | |
| Flow : 3.18mm | 1.2 | % | |
| Transverse flow : 1.59mm | 1.0 | % | |
| Transverse flow : 3.18mm | 0.80 | % |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 5 sec) | 85 | ASTM D2240, ISO 48 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel) | 160 | mg | ASTM D3389 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Set (100% Strain) | 19 | % | ASTM D412 |
| Tensile Stress (100% Strain, 23°C) | 10.1 | MPa | ASTM D412, ISO 37 |
| Tensile Strength (Yield, 23°C) | 14.7 | MPa | ASTM D412, ISO 37 |
| Tensile Elongation (Break, 23°C) | 260 | % | ASTM D412, ISO 37 |
| Tear Strength 1(24°C) | 54.3 | kN/m | ASTM D624 |
| Compression Set | ASTM D395, ISO 815 | ||
| 24°C, 22 hr | 23 | % | ASTM D395, ISO 815 |
| 70°C, 22 hr | 65 | % | ASTM D395, ISO 815 |
| 100°C, 22 hr | 82 | % | ASTM D395, ISO 815 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength in Air | |||
| 70°C, 168 hr | -16 | % | ASTM D573, ISO 188 |
| 100% strain, 70°C, 168 hr | -4.0 | % | ASTM D573 |
| 100°C, 168 hr | -19 | % | ASTM D573, ISO 188 |
| 100% strain, 100°C, 168 hr | -6.0 | % | ASTM D573 |
| 100% strain 70°C, 168 hr | -4.0 | % | ISO 188 |
| 100% strain 100°C, 168 hr | -6.0 | % | ISO 188 |
| Change in Ultimate Elongation in Air | ASTM D573, ISO 188 | ||
| 70°C, 168 hr | -15 | % | ASTM D573, ISO 188 |
| 100°C, 168 hr | -21 | % | ASTM D573, ISO 188 |
| Change in Volume | |||
| 24°C, 168 hr, in reference fuel B | 87 | % | ASTM D471 |
| 70°C, 168 hr, ASTM Standard Oil (No. 1) | 27 | % | ASTM D471 |
| 70°C, 168 hr, in IRM 903 oil | 130 | % | ASTM D471 |
| 70°C, 168 hr, in water | 1.0 | % | ASTM D471, ISO 1817 |
| 24°C, 168 hr, in reference fuel B | 87 | % | ISO 1817 |
| 70°C, 168 hr, in ASTM #1 oil | 27 | % | ISO 1817 |
| 70°C, 168 hr, in IRM 903 oil | 130 | % | ISO 1817 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | -51.1 | °C | ASTM D746, ISO 812 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melt Viscosity (190°C, 300 sec^-1) | 1060 | Pa·s | ASTM D3835 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature - Desiccant Dryer | 65.6 | °C | |
| Drying Time - Desiccant Dryer | 3.0 | hr | |
| Suggested Max Regrind | 25 | % | |
| Rear Temperature | 204 - 221 | °C | |
| Middle Temperature | 216 - 227 | °C | |
| Front Temperature | 227 - 238 | °C | |
| Nozzle Temperature | 227 - 249 | °C | |
| Processing (Melt) Temp | 227 - 254 | °C | |
| Mold Temperature | 43.3 - 54.4 | °C | |
| Injection Pressure | 1.03 - 3.45 | MPa | |
| Screw Speed | 25 - 100 | rpm |
| Injection instructions |
|---|
| Injection Speed: 1 to 3 in³/secInjection Time (1st Stage/Boost): 0.5 to 2 secSecond Stage Pressure: 150 to 300 psiSecond Stage Time: 3 to 10 secCooling Time: 10 to 20 secBack Pressure: 20 to 50 % |
| Note Message | |
|---|---|
| 1 . | C mould |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Kepital® F20-03 BBK | KEP Americas | Acetal (POM) Copolymer | Kepital® |
| IDI BMC 46-3 | IDI Composites International | TS, Unspecified | IDI BMC |
| Leona™ MR001 | Asahi Kasei Chemicals Corporation | Nylon 66 | Leona™ |
| Sylvin 2981-80 Natural | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
| LGG 1044 | LG Polymers India Pvt. Ltd. | PS (GPPS) | LGG |
