Order Products : sales@su-jiao.com
Fortron® 0214
| Category: | PPS , Polyphenylene Sulfide |
| Manufacturer: | Celanese Corporation |
| Trademark: | Fortron® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | mQma55_Fortron-0214.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| 0214 is an unfilled grade exhibiting good melt strength. This grade demonstrates excellent heat and chemical resistance. It can be extruded to produce multi-filaments. Due to the excellent balance of flow and melt strength, this product is occasionally used for injection molding parts. Available standard in powder (0214B1), pellet (0214P1) and crystallized pellet (0214C1) form. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Multi-Point Data |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.35 | g/cm³ | ASTM D792, ISO 1183 |
| Specific Volume | 0.741 | cm³/g | ASTM D792 |
| Viscosity | 120 | Pa·s | Internal method |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density of Melt | 1.150 | g/cm³ | Internal method |
| Specific Heat Capacity of Melt | 1830 | J/kg/°C | Internal method |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Temperature | 310 | °C | Internal method |
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Molding Shrinkage | |||
| Flow | 1.2 | % | ASTM D955 |
| Transverse flow | 1.0 | % | ASTM D955 |
| Vertical flow direction | 1.5 - 1.8 | % | ISO 294-4 |
| Flow direction | 1.2 - 1.5 | % | ISO 294-4 |
| Water Absorption (Saturation, 23°C) | 0.020 | % | ISO 62 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness | |||
| Class m | 93 | ASTM D785 | |
| M scale | 95 | ISO 2039-2 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | 3800 | MPa | ISO 527-2/1A/1 |
| Tensile Strength | |||
| Fracture, 23°C | 86.2 | MPa | ASTM D638 |
| Fracture | 90.0 | MPa | ISO 527-2/1A/5 |
| Tensile Elongation | |||
| Fracture, 23°C | 3.0 | % | ASTM D638 |
| Fracture | 3.0 | % | ISO 527-2/1A/5 |
| Flexural Modulus (23°C) | 3750 | MPa | ISO 178 |
| Flexural Stress 1 | 125 | MPa | ISO 178 |
| Coefficient of Friction (vs. Steel - Dynamic) | 0.14 | Internal method |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact (23°C) | 3.5 | kJ/m² | ISO 180/1A |
| Unnotched Izod Impact Strength (23°C) | 45 | kJ/m² | ISO 180/1U |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | |||
| 0.45 MPa, annealed | 204 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 104 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 110 | °C | ISO 75-2/A |
| 8.0 MPa, not annealed | 95.0 | °C | ISO 75-2/C |
| Glass Transition Temperature 2 | 90.0 | °C | ISO 11357-2 |
| Melting Temperature 3 | 280 | °C | ISO 11357-3 |
| Linear thermal expansion coefficient | ISO 11359-2 | ||
| Flow | 5.2E-5 | cm/cm/°C | ISO 11359-2 |
| Lateral | 5.3E-5 | cm/cm/°C | ISO 11359-2 |
| Thermal Conductivity | 3.5 | W/m/K | ASTM C177 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | |||
| -- | 1.0E+16 | ohms·cm | ASTM D257 |
| -- | 1.0E+11 | ohms·cm | IEC 60093 |
| Dielectric Strength | |||
| -- 4 | 18 | kV/mm | ASTM D149 |
| -- | 18 | kV/mm | IEC 60243-1 |
| Dielectric Constant | ASTM D150 | ||
| 1 kHz | 3.00 | ASTM D150 | |
| 1 MHz | 3.00 | ASTM D150 | |
| Dissipation Factor | ASTM D150 | ||
| 1 kHz | 1.0E-3 | ASTM D150 | |
| 1 MHz | 9.0E-4 | ASTM D150 | |
| Arc Resistance | 124 | sec | ASTM D495 |
| Comparative Tracking Index | 125 | V | IEC 60112 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 110 - 120 | °C | |
| Drying Time | 3.0 - 4.0 | hr | |
| Suggested Max Moisture | 0.020 | % | |
| Hopper Temperature | 20.0 - 30.0 | °C | |
| Rear Temperature | 290 - 300 | °C | |
| Middle Temperature | 300 - 310 | °C | |
| Front Temperature | 310 - 320 | °C | |
| Nozzle Temperature | 300 - 310 | °C | |
| Processing (Melt) Temp | 310 - 320 | °C | |
| Mold Temperature | 140 - 160 | °C | |
| Injection Pressure | 40.0 - 80.0 | MPa | |
| Injection Rate | Fast | ||
| Holding Pressure | 30.0 - 60.0 | MPa | |
| Back Pressure | 0.00 - 3.00 | MPa |
| Injection instructions |
|---|
| Manifold Temperature: 310 to 320°CZone 4 Temperature: 310 to 320°CFeed Temperature: 60 to 80°C |
| Note Message | |
|---|---|
| 1 . | Break |
| 2 . | 10°C/min |
| 3 . | 10°C/min |
| 4 . | Method A (short time) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Prime Polypro™ F327BV | Prime Polymer Co., Ltd. | PP Random Copolymer | Prime Polypro™ |
| Sup-tech B706 | Shanghai Suptech Engineering Plastics Co. Ltd. | Nylon 6 | Sup-tech |
| KumhoSunny PC/ABS HAC8240B | Shanghai KumhoSunny Plastics Co., Ltd. | PC+ABS | KumhoSunny PC/ABS |
| LNP™ THERMOCOMP™ EC006PXQ compound | SABIC Innovative Plastics | PEI | LNP™ THERMOCOMP™ |
| Sylvin 29168-95 Clear | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
