Order Products : sales@su-jiao.com
LUBMER™ L5000
| Category: | HMWPE , High Molecular Weight Polyethylene |
| Manufacturer: | Mitsui Chemicals America, Inc. |
| Trademark: | LUBMER™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | locxQ6_LUBMER-L5000.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
LUBMER™L5000 is a high molecular weight polyethylene material,. This product is available in North America,. LUBMER™The main features of L5000 are:
Typical application areas include:
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Forms |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 0.966 | g/cm³ | ASTM D792 |
| Molding Shrinkage | ASTM D955 | ||
| Flow : 2.00mm | 1.8 | % | ASTM D955 |
| Transverse flow : 2.00mm | 1.6 | % | ASTM D955 |
| Water Absorption (24 hr) | 0.010 | % | ASTM D570 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 51 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength 1(Break, 23°C) | 47.0 | MPa | ASTM D638 |
| Tensile Elongation 2(Break, 23°C) | 10 | % | ASTM D638 |
| Flexural Modulus 3(23°C, 3.00mm, 48.0mm span) | 1620 | MPa | ASTM D790 |
| Flexural Strength 4(yield, 23°C, 3.00mm, 48.0mm span) | 38.0 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact (23°C, 2.00 mm) | 190 | J/m | ASTM D256 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load (0.45 MPa, Unannealed) | 80.0 | °C | ASTM D648 |
| Vicat Softening Temperature | 130 | °C | ASTM D1525 5 |
| CLTE - Flow | 1.3E-4 | cm/cm/°C | ASTM D696 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric Strength | 44 | kV/mm | ASTM D149 |
| Dielectric Constant (23°C) | 2.40 | ASTM D150 | |
| Dissipation Factor (1 MHz) | 1.0E-4 | ASTM D150 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating (1.59 mm) | HB | UL 94 |
| Additional Information |
|---|
| Kinetic Coefficient of Friction, MCI Method, Lubmer-contact material, SUS 304, surface roughness, 6S: 0.09Heat generation temp, MCI Method, Lubmer-contact material, SUS 304, surface roughness, 6S: 67°C (30 MPa m/min)Critical PV value, MCI Method, Lubmer-contact material, SUS 304, surface roughness, 6S: >/= 30 MPa m/minAbrasion Loss, MCI Method, Lubmer-contact material, SUS 304, surface roughness, 6S: 150E-10 cm³/ kg-mVolume Resistivity, ASTM D257: 1E17 to 1E18 ohm-cmDissipation Factor, ASTM D150, 1MHz: 1E-4 to 2E-4Spiral Flow, MCI method, 4.8mm radius: 30 cm (270°C)The values listed as Mold Shrink, Linear Flow and Trans, ASTM D955, were tested in accordance with MCI methods. |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Rear Temperature | 210 | °C | |
| Middle Temperature | 245 | °C | |
| Front Temperature | 270 | °C | |
| Nozzle Temperature | 270 | °C | |
| Mold Temperature | 24.0 - 40.0 | °C | |
| Injection Pressure | 98.1 | MPa | |
| Injection Rate | Moderate |
| Note Message | |
|---|---|
| 1 . | Type 5, 50mm/min |
| 2 . | Type 5, 50mm/min |
| 3 . | 5.0 mm/min |
| 4 . | 5.0 mm/min |
| 5 . | 压 力1 (10N) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Tecotek® PC40 GR30 NL | Eurotec Engineering Plastics | PC | Tecotek® |
| TEKAMID™ TA250G33 | Mando Advanced Materials Co., Ltd. | Nylon 66 | TEKAMID™ |
| SureSpec HD60-800F | Genesis Polymers | HDPE | SureSpec |
| Nypol® PA A3 G25 PRTA010 NR438 | Petropol Industry and Trade of Polymers LTDA | Nylon 66 | Nypol® PA |
| POLYCOMPO PP F113G | POLYCOMPO Co.,Ltd. | PP, Unspecified | POLYCOMPO PP |
