Vyncolit® TEM 9010 Datasheet,Epoxy,Vyncolit N.V.-SHANGHAI SUSHENG

Message
Vyncolit TEM 9010 is an epoxy. Epoxy resin material, containing filler glass fiber reinforced material. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific. The processing methods are: resin transfer molding, compression molding or injection molding. The main features of Vyncolit TEM 9010 are: chemical resistance low viscosity Good toughness Heat resistance Typical application areas include: Electrical/electronic applications food contact applications military applications

General Information
Filler / Reinforcement	Glass fiber reinforced material
Features	The degassing effect is low to no Low viscosity Solvent resistance Anti-salt water/fog Good thermal shock resistance Good chemical resistance alkali resistance acid resistance Good toughness Non-corrosive
Uses	Electrical components Military application Connector
Agency Ratings	FDA not rated USDA Unspecified Approval
Forms	Particles
Processing Method	Resin transfer molding Compression molding Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.77	g/cm³	ASTM D792
Bulk Factor	2.1		ASTM D1895
Molding Shrinkage - Flow (Transfer Molded)	0.25	%	ASTM D955

Hardness	Nominal Value	Unit	Test Method
Rockwell Hardness (M-Scale)	110		ASTM D785

Mechanical	Nominal Value	Unit	Test Method
Tensile Strength	96.5	MPa	ASTM D638
Flexural Modulus	17200	MPa	ASTM D790
Flexural Strength	159	MPa	ASTM D790
Compressive Strength	207	MPa	ASTM D695

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact	43	J/m	ASTM D256A

Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load (1.8 MPa, Unannealed)	160	°C	ASTM D648
CLTE - Flow	4.0E-5	cm/cm/°C	ASTM D696
Thermal Conductivity	0.33	W/m/K	ASTM C177

Electrical	Nominal Value	Unit	Test Method
Dielectric Strength			ASTM D149
-- ¹	15	kV/mm	ASTM D149
-- ²	14	kV/mm	ASTM D149
Dielectric Constant (1 MHz)	4.00		ASTM D150
Dissipation Factor (1 MHz)	0.014		ASTM D150
Arc Resistance	180	sec	ASTM D495

Injection	Nominal Value	Unit
Middle Temperature	60.0 - 82.2	°C
Nozzle Temperature	82.2 - 93.3	°C
Processing (Melt) Temp	93.3 - 116	°C
Mold Temperature	149 - 177	°C
Injection Pressure	34.5 - 68.9	MPa
Holding Pressure	13.8 - 34.5	MPa
Back Pressure	0.345	MPa

Injection instructions
Gauge: 0.3The value listed as Thermal Conductivity, ASTM C177, was tested in accordance with ASTM F433.Water Absorption, ASTM D570, 48 hrs, 50°C: 0.27%Dielectric Strength, ASTM D149, 60 Hz, Method A, wet: 390 V/milDielectric Strength, ASTM D149, 60 Hz, Method A, dry: 400 V/milDielectric Strength, ASTM D149, 60 Hz, Method B, wet: 350 V/milDielectric Strength, ASTM D149, 60 Hz, Method B, dry: 350 V/milDielectric Constant, ASTM D150, 1000000 Hz, dry: 4Dissipation Factor, ASTM D150, 1000000 Hz, dry: 0.014Bulk Factor, ASTM D1895: 2 to 2.2Compression and Transfer Molding Conditions: Preheat Temperature: 180 to 225 °F Mold Temperature: 325 to 370 °F Compression Mold Pressure: 1000 to 5000 psi Transfer Mold Pressure: 1500 to 8000 psi Cure Time, 0.125 in: 60 to 90 sec

Injection instructions

Gauge: 0.3The value listed as Thermal Conductivity, ASTM C177, was tested in accordance with ASTM F433.Water Absorption, ASTM D570, 48 hrs, 50°C: 0.27%Dielectric Strength, ASTM D149, 60 Hz, Method A, wet: 390 V/milDielectric Strength, ASTM D149, 60 Hz, Method A, dry: 400 V/milDielectric Strength, ASTM D149, 60 Hz, Method B, wet: 350 V/milDielectric Strength, ASTM D149, 60 Hz, Method B, dry: 350 V/milDielectric Constant, ASTM D150, 1000000 Hz, dry: 4Dissipation Factor, ASTM D150, 1000000 Hz, dry: 0.014Bulk Factor, ASTM D1895: 2 to 2.2Compression and Transfer Molding Conditions: Preheat Temperature: 180 to 225 °F Mold Temperature: 325 to 370 °F Compression Mold Pressure: 1000 to 5000 psi Transfer Mold Pressure: 1500 to 8000 psi Cure Time, 0.125 in: 60 to 90 sec

Note Message
1 .	Method A (short time)
2 .	Method B (step by step)

Category:	Epoxy , Epoxy; Epoxide
Manufacturer:	Vyncolit N.V.
Trademark:	Vyncolit®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	iMVSYt_Vyncolit-TEM-9010.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
SOLPLAST TH 7000D	UTEKSOL d.o.o.	SBS	SOLPLAST TH
VECTOR® 4211N	TSRC Corporation	SIS	VECTOR®
LUVOCOM® 1/CF/30	Lehmann & Voss & Co.	Nylon 66	LUVOCOM®
Sylvin 83028-90 Black	Sylvin Technologies Incorporated	PVC, Unspecified	Sylvin
Sylvin 8773-60D White 1430	Sylvin Technologies Incorporated	PVC, Rigid	Sylvin