Order Products : sales@su-jiao.com
Monprene® RG-19255
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Teknor Apex Company |
| Trademark: | Monprene® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | hxMtpF_Monprene-RG-19255.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| Monprene MP-1500 is a thermoplastic elastomer designed for the consumer market. Monprene MP-1500 is a clear, medium hardness grade that exhibits low compression set, good abrasion and chemical resistance, and is suitable for injection molding and extrusion. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 0.868 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (175°C/2.16 kg) | 50 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness | ASTM D2240 | ||
| Shaw A | 57 | ASTM D2240 | |
| Shaw A, 5 seconds | 55 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ASTM D412 | ||
| Transverse flow : 100% strain 1 | 1.85 | MPa | ASTM D412 |
| Flow : 100% strain 2 | 2.24 | MPa | ASTM D412 |
| Transverse flow : 300% strain 3 | 2.61 | MPa | ASTM D412 |
| Flow : 300% strain 4 | 3.12 | MPa | ASTM D412 |
| Tensile Strength 5 | ASTM D412 | ||
| Transverse flow : Fracture | 2.92 | MPa | ASTM D412 |
| Flow : Fracture | 3.58 | MPa | ASTM D412 |
| Tensile Elongation | ASTM D412 | ||
| Fracture | 650 | % | ASTM D412 |
| Transverse flow : Fracture 6 | 440 | % | ASTM D412 |
| Flow : Fracture 7 | 450 | % | ASTM D412 |
| Tear Strength 8 | ASTM D624 | ||
| Transverse flow | 19.1 | kN/m | ASTM D624 |
| Flow | 20.5 | kN/m | ASTM D624 |
| Compression Set 9 | ASTM D395B | ||
| 23°C, 22 hr | 33 | % | ASTM D395B |
| 70°C, 22 hr | 94 | % | ASTM D395B |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Rear Temperature | 160 - 210 | °C | |
| Middle Temperature | 166 - 216 | °C | |
| Front Temperature | 171 - 221 | °C | |
| Nozzle Temperature | 177 - 227 | °C | |
| Processing (Melt) Temp | 177 - 227 | °C | |
| Mold Temperature | 15.6 - 37.8 | °C | |
| Injection Pressure | 1.38 - 5.52 | MPa | |
| Injection Rate | Fast | ||
| Back Pressure | 0.172 - 0.689 | MPa | |
| Screw Speed | 50 - 100 | rpm | |
| Cushion | 3.81 - 25.4 | mm |
| Injection instructions |
|---|
| Drying is not necessary. However, if moisture is a problem, dry the pellets for 2 to 4 hours at 150°F (65°C). |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 182 - 232 | °C | |
| Cylinder Zone 2 Temp. | 188 - 238 | °C | |
| Cylinder Zone 3 Temp. | 193 - 243 | °C | |
| Cylinder Zone 5 Temp. | 199 - 249 | °C | |
| Die Temperature | 199 - 249 | °C |
| Extrusion instructions |
|---|
| Screw Speed: 30 to 100 rpm |
| Note Message | |
|---|---|
| 1 . | Mouth die C, 510mm/min |
| 2 . | Mouth die C, 510mm/min |
| 3 . | C mold, 510mm/min |
| 4 . | C mold, 510mm/min |
| 5 . | C mold, 510mm/min |
| 6 . | Mouth die C, 510mm/min |
| 7 . | Mouth die C, 510mm/min |
| 8 . | C mold, 510mm/min |
| 9 . | Type 1 |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Spartech Polycom SC14-1233L | Spartech Polycom | Nylon 66 | Spartech |
| SureSpec LLC4-020 | Genesis Polymers | LLDPE | SureSpec |
| UMG ALLOY® TA-15W | UMG ABS, Ltd. | ASA+PC | UMG ALLOY® |
| CYCOM® 2237 | Cytec Industries Inc. | PI, TS | CYCOM® |
| Glastic® 210 | Glastic Corporation | Polyester, TS | Glastic® |
