Order Products : sales@su-jiao.com

MEGOLON™ S340

Category:	TP, Unspecified , Thermoplastic
Manufacturer:	AlphaGary
Trademark:	MEGOLON™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	gO7rUd_MEGOLON-S340.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

WECHAT

Message

MEGOLON™ S340 is a thermoplastic, halogen free, fire retardant cable sheathing compound for general purpose applications. MEGOLON™ S340 exhibits an enhanced fire test performance with a high oxygen index whilst retaining similar mechanical properties to MEGOLON™ S300

APPLICATIONS

UK: BS 7655:6.1 types LTS1 and LTS3, BS7878:7 (HD 624.7 S1) and LUL SE569. MEGOLON™ S340 also meets the requirements of BS 7655:4.1 type TM1 for a general purpose PVC sheathing compound

Germany: DIN VDE 0207, part 24, type HM2

France: Norme Francaise NF C 32-323

General Information
Features	Flame Retardant General Purpose Halogen Free
Uses	Cable Jacketing General Purpose
Agency Ratings	BS 7655 4.1 type TM1 BS 7655:6.1 Type LTS 1 BS 7655:6.1 Type LTS 3 BS 7878:7 (HD 624.7 S1) DIN VDE 0207, Part 24, Type HM2 NFC 32-323
Forms	Pellets
Processing Method	Extrusion

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.55	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (150°C/21.6 kg)	4.5	g/10 min	ISO 1133
Mooney Viscosity (ML 1+4, 140°C)	45	MU	ASTM D1646

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore D)	58		ASTM D2240

Mechanical	Nominal Value	Unit	Test Method
Tensile Stress
-- ¹	18.0	MPa	IEC 60811-1-2
--	14.5	MPa	IEC 60811-1-1
Tensile Strain
Break ²	120	%	IEC 60811-1-2
Break	150	%	IEC 60811-1-1
Elongation at Break
after 4 hours, in IRM 902 Oil : 70°C	170	%
after 7 days, in IRM 902 Oil : 23°C	140	%
after 7 days, in IRM 903 Oil : 23°C	150	%
Tensile Strength
after 4 hours, in IRM 902 Oil : 70°C	13.0	MPa
after 7 days, in IRM 902 Oil : 23°C	13.0	MPa
after 7 days, in IRM 903 Oil : 23°C	11.5	MPa

Thermal	Nominal Value	Unit	Test Method
Cold Elongation (-25°C)	65	%	IEC 60811-1-4
Cold Impact (-25°C)	pass		IEC 60811-1-4
Hot Deformation (90°C)	2.0	%	BS 6469 99.1
Hot Pressure Test (80°C)	15	%	IEC 60811-3-1

Electrical	Nominal Value	Unit	Test Method
Insulation Resistance			BS 6469 99.2
20°C	1.0E+14	ohms·cm
after 12 hours immersion in water : 20°C	5.0E+13	ohms·cm

Flammability	Nominal Value	Unit	Test Method
Acid Gas Emission Conductivity	28.0	µS/cm	IEC 60754-2
Acid Gas Emission pH	4.30		IEC 60754-2
Flammability Temperature Index	300	°C	ISO 4589-3
Smoke Density			ASTM E662
Flaming mode ³	< 120	Ds
Non-flaming mode ⁴	< 270	Ds
Toxicity	2.00		NES 713

Additional Information	Nominal Value	Unit	Test Method
Halogen Acid Gas Evolution	0.0	%	IEC 60754-1
Ozone Resistance	pass		ASTM D470

Extrusion	Nominal Value	Unit
Draw Down	1.5:1.0
Extruder Screw Compression Ratio	1.0:1.0 to 2.0:1.0

Elastomers	Nominal Value	Unit	Test Method
Tear Strength	5.00	kN/m	BS 6469 99.1

Aging	Nominal Value	Unit	Test Method
Change in Tensile Strength in Air (100°C, 168 hr)	26	%
Change in Tensile Strain at Break in Air (100°C, 168 hr)	-23	%
Change in Tensile Stress
23°C, 168 hr, in IRM 902 Oil	-10	%
23°C, 168 hr, in IRM 903 Oil	-20	%
70°C, 4 hr, in IRM 902 Oil	-10	%
70°C, 168 hr, in Water	0.0	%	BS 6469 99.1
Change in Tensile Strain at Break
23°C, 168 hr, in IRM 902 Oil	-10	%
23°C, 168 hr, in IRM 903 Oil	0.0	%
70°C, 4 hr, in IRM 902 Oil	10	%
70°C, 168 hr, in Water	-15	%	BS 6469 99.1
Change in Volume
23°C, 168 hr, in IRM 902 Oil	1.0	%
23°C, 168 hr, in IRM 903 Oil	10	%
70°C, 4 hr, in IRM 902 Oil	3.0	%

Electrical	Nominal Value	Unit	Test Method
Dielectric Constant (50 Hz)	4.80		ASTM D150
Dissipation Factor (50 Hz)	0.020		ASTM D150

Flammability	Nominal Value	Unit	Test Method
Oxygen Index	40	%	ISO 4589-2

Extrusion	Nominal Value	Unit
Drying Temperature	60.0 to 70.0	°C
Cylinder Zone 1 Temp.	135	°C
Cylinder Zone 2 Temp.	140	°C
Cylinder Zone 3 Temp.	145	°C
Cylinder Zone 4 Temp.	150	°C
Cylinder Zone 5 Temp.	160	°C
Melt Temperature	165 to 175	°C
Die Temperature	165	°C

Note Message
1 .	after 7 days at 100°C
2 .	after 7 days at 100°C
3 .	Time to maximum: 10 minutes
4 .	Time to maximum: 13 minutes

Resin Grade	Manufacturer	Category	Trademark
STERalloy™ FDG 2056-5	Hapco Inc.	TP, Unspecified	STERalloy™ FDG
ADDINYL C2 V30	ADDIPLAST	Nylon 66/6	ADDINYL
AFFINITY™ PL 1888G	The Dow Chemical Company	POP	AFFINITY™
POCAN® A 3131 000000	LANXESS Corporation	PBT+ASA	POCAN®
Durethan® BG 30 X H2.0 901510	LANXESS GmbH	Nylon 6	Durethan®