Order Products : sales@su-jiao.com
Generic PEBA-Ether
| Category: | PEBA-Ether , Polyether Block Amide |
| Manufacturer: | Generic |
| Trademark: | Generic |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | eK0XVm_Generic-PEBA-Ether.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
This data represents typical values that have been calculated from all products classified as: Generic PEBA-Ether This information is provided for comparative purposes only. |
| General Information |
|---|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | |||
| -- | 1.01 - 1.15 | g/cm³ | ASTM D792 |
| 23°C | 1.00 - 1.15 | g/cm³ | ISO 1183 |
| -- | 1020 | kg/m³ | ISO 1183 1 |
| Melt Mass-Flow Rate (MFR) (235°C/1.0 kg) | 2.0 - 8.0 | g/10 min | ASTM D1238 |
| Molding Shrinkage (23°C) | 0.40 - 1.5 | % | ISO 294-4 |
| Water Absorption | |||
| 23°C, 24 hr | 1.2 | % | ASTM D570 |
| 23°C, 24 hr | 0.70 - 3.7 | % | ISO 62 |
| Saturation | 2.4 | % | ISO 62 2 |
| Equilibrium, 23°C, 50% RH | 0.40 - 1.4 | % | ISO 62 |
| Balance | 0.60 | % | ISO 62 3 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness | |||
| 23°C | 25 - 90 | ASTM D2240 | |
| 23°C | 22 - 72 | ISO 868 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | |||
| 23°C | 177 - 371 | MPa | ISO 527-2 |
| -- | 215 | MPa | ISO 527-2 4 |
| Tensile Stress | |||
| Yield, 23°C | 9.00 - 74.0 | MPa | ISO 527-2 |
| Fracture, 23°C | 28.6 - 60.0 | MPa | ASTM D638 |
| 50% strain | 8.00 | MPa | ISO 527-2 5 |
| Tensile Elongation | |||
| Fracture, 23°C | 340 - 750 | % | ASTM D638 |
| Fracture, 23°C | 190 - 210 | % | ISO 527-2 |
| Flexural Modulus | |||
| 23°C | 15.9 - 417 | MPa | ASTM D790 |
| 23°C | 12.0 - 406 | MPa | ISO 178 |
| Flexural Strength (Yield, 23°C) | 1.20 - 15.0 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength (23°C) | 97 - 120 | kJ/m² | ISO 179 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Vicat Softening Temperature | |||
| -- | 60.0 - 165 | °C | ASTM D1525 |
| -- | 58.0 - 175 | °C | ISO 306 |
| Melting Temperature | |||
| -- | 125 - 176 | °C | |
| -- | 134 - 195 | °C | ISO 11357-3 |
| -- 6 | 169 | °C | ISO 11357-3 7 |
| CLTE - Flow | 1.4E-4 - 2.5E-4 | cm/cm/°C | ASTM D696 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Surface Resistivity | |||
| -- | 4.0E+8 - 5.0E+10 | ohms | ASTM D257 |
| -- | 5.5E+3 - 4.6E+12 | ohms | IEC 60093 8 |
| Volume Resistivity | |||
| 23°C | 4.0E+8 - 1.0E+13 | ohms·cm | ASTM D257 |
| -- | 2.5E+6 - 2.3E+10 | ohms·m | IEC 60093 9 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 60.0 - 82.5 | °C | |
| Drying Time | 3.9 - 6.0 | hr | |
| Processing (Melt) Temp | 209 - 267 | °C | |
| Mold Temperature | 20.0 - 43.0 | °C |
| Injection instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic PEBA-EtherThis information is provided for comparative purposes only. |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 60.0 - 75.6 | °C | |
| Drying Time | 5.0 - 6.0 | hr | |
| Melt Temperature | 204 - 237 | °C |
| Extrusion instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic PEBA-EtherThis information is provided for comparative purposes only. |
| Note Message | |
|---|---|
| 1 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 2 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 3 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 4 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 5 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 6 . | 10 °C/min |
| 7 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 8 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 9 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| QR Resin QR-2008-FR | QTR, Inc. | ABS | QR Resin |
| Sipolprene® 46185 B | SIPOL S.p.A | TPC-ET | Sipolprene® |
| ALCUDIA® HDPE TR-131 | REPSOL | HDPE | ALCUDIA® HDPE |
| Delta ATR-2G40 | Delta Polymers | Acetal (POM) Copolymer | Delta |
| Braskem PE LL5405S | Braskem | LLDPE | Braskem PE |
