Order Products : sales@su-jiao.com
UBESTA 3030 JI7
| Category: | Nylon 12 , Polyamide 12 |
| Manufacturer: | UBE Engineering Plastics, S.A. |
| Trademark: | UBESTA |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | e2Lu4z_UBESTA-3030-JI7.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| UBESTA 3030 JI7 is a plasticized and impact modified PA12 grade with special low migration properties. Special fields of application can be pneumatic or hydraulic tubes where integrity of sealing O-rings is most important. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.00 | g/cm³ | ISO 1183 |
| Melt Mass-Flow Rate (MFR) (235°C/2.16 kg) | 4.0 | g/10 min | ISO 1133 |
| Molding Shrinkage | ISO 294-4 | ||
| Vertical flow direction | 1.5 | % | ISO 294-4 |
| Flow direction | 0.50 | % | ISO 294-4 |
| Water Absorption (23°C, 24 hr) | 0.60 | % | ISO 62 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 49 | ISO 2039-2 | |
| Durometer Hardness (Shore D) | 68 | ISO 868 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (Yield) | 30.0 | MPa | ISO 527-2 |
| Tensile Strain (Break) | 200 | % | ISO 527-2 |
| Flexural Modulus | 400 | MPa | ISO 178 |
| Flexural Stress | 19.0 | MPa | ISO 178 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -40°C, complete fracture | 6.0 | kJ/m² | ISO 179/1eA |
| 23°C, local fracture | 110 | kJ/m² | ISO 179/1eA |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Deflection Temperature | |||
| 0.45 MPa, not annealed | 88.0 | °C | ISO 75-2/B |
| 1.8 MPa, not annealed | 47.0 | °C | ISO 75-2/A |
| Melting Temperature (DSC) | 174 | °C | ISO 3146 |
| CLTE - Flow | 1.6E-4 | cm/cm/°C | ISO 11359-2 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | 1.0E+13 | ohms·cm | IEC 60093 |
| Additional Information |
|---|
| The value listed as Melting Temperature, ISO 3146, was tested in accordance with ISO 11357.Tensile Strain at Break, ISO 527: >200%Tensile Stress at Yield, ISO 527: >30 MPaAbrasion Loss, ISO 9352, CS-17, 1000 rev.: 8 mg |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| SABIC® LDPE 2201H1W | Saudi Basic Industries Corporation (SABIC) | LDPE | SABIC® LDPE |
| Radel® R-7535 | Solvay Specialty Polymers | PPSU | Radel® |
| VECTOR® 4215A | Dexco Polymers LP | SIS+SI | VECTOR® |
| ADEKA EP-4000 | Adeka Corporation | Epoxy | ADEKA |
| Borealis PE FA7224 | Borealis AG | LDPE | Borealis PE |
