Order Products : sales@su-jiao.com
Dynaflex™ G7690-9 (Black)
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | Dynaflex™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | dcaMZh_Dynaflex-G7690-9-Black-.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
Dynaflex™G7690-9 (Black) is an easy-to-process universal TPE designed for a wide range of applications, including applications that must comply with FDA standards.
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.18 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (200°C/5.0 kg) | 14 | g/10 min | ASTM D1238 |
| Molding Shrinkage - Flow | 0.60 - 1.4 | % | ASTM D955 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 10 sec) | 89 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress 1 | ASTM D412 | ||
| 100% strain, 23°C 2 | 4.55 | MPa | ASTM D412 |
| 300% strain, 23°C 3 | 6.21 | MPa | ASTM D412 |
| Tensile Strength (Break, 23°C) | 11.0 | MPa | ASTM D412 |
| Tensile Elongation (Break, 23°C) | 600 | % | ASTM D412 |
| Tear Strength | 46.4 | kN/m | ASTM D624 |
| Compression Set (23°C, 22 hr) | 38 | % | ASTM D395B |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Apparent Viscosity | ASTM D3835 | ||
| 200°C, 1340 sec^-1 | 74.0 | Pa·s | ASTM D3835 |
| 200°C, 11200 sec^-1 | 14.3 | Pa·s | ASTM D3835 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Suggested Max Regrind | 20 | % | |
| Rear Temperature | 166 - 177 | °C | |
| Middle Temperature | 177 - 193 | °C | |
| Front Temperature | 188 - 227 | °C | |
| Nozzle Temperature | 193 - 227 | °C | |
| Mold Temperature | 15.6 - 37.8 | °C | |
| Back Pressure | 0.00 - 0.827 | MPa | |
| Screw Speed | 40 - 100 | rpm |
| Injection instructions |
|---|
| 在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Dynaflex™ G7690-9（黑色）可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Dynaflex™ G7690-9（黑色）具有极好的熔体稳定性。最长停留时间可能会根据机筒尺寸有所变化。通常，如果机器闲置 8 - 10 分钟或以上，则应将机筒排空。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：350 - 900 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：3 - 10 秒保持时间（薄部件）：1 - 3 秒 |
| Note Message | |
|---|---|
| 1 . | 2 hours |
| 2 . | Mouth die c |
| 3 . | C mould |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Nipol® AR 71 | Zeon Corporation | Rubber | Nipol® AR |
| APICAL 150AF019 | Kaneka Corporation | PI, TS | APICAL |
| Huafon HF-4390A | Huafon Group Co., Ltd. | TPU-Polyether | Huafon |
| Sylvin 9768-80UV Natural | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
| CYCOLAC™ INP562 resin | SABIC Innovative Plastics | ABS+SAN | CYCOLAC™ |
