Lusin® Lub O 32 F

Category:	Unspecified , Unspecified
Manufacturer:	Chem-Trend L.P.
Trademark:	Lusin®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	cy11lz_LusinLubO32F.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
Lubricant and Release Agent with 100% Active Ingredient Benefits Solvent and silicone free Environmentally friendly 100% active ingredient The formulation meets the requirements of 21 CFR §178.3570 "lubricants with incidental food contact" According to 21 CFR §175.300 the product can be used as resinous and polymeric coating The formulation is in compliance with European Plastics Regulation No 10/2011 Description In general Lusin® Lub O 32 F can be used as lubricant or release agent in the packaging industry. If the product is applied on a die, e. g. in blown film applications, it reduces the build up during production. Lusin® Lub O 32 F, applied to the outside surface of PET preforms significantly reduces scratches to the plastic surfaces occurring during transport and handling. The blocking of bottles during the transport using air conveyors can be reduced to an absolute minimum by means of coating the preforms or the final bottles with Lusin® Lub O 32 F. Application In terms of lubrication of the outside surface of PET preforms, Lusin® Lub O 32 F should be applied using a suitable spray equipment, e.g. Steidle equipment. The product is also suitable as a release agent in the thermoplastic processing industry. Mould temperatures should not exceed 200°C in terms of injection moulding. For film applications the die temperature should not exceed 190°C. Lusin® Lub O 32 F is a waterless system. Therefore we strongly advise against dilution with water since even small impurities of water in the machinery and especially in the tubes will cause agglomerates that may block the system.

Message

Lubricant and Release Agent with 100% Active Ingredient

Benefits

Solvent and silicone free

Environmentally friendly

100% active ingredient

The formulation meets the requirements of 21 CFR §178.3570 "lubricants with incidental food contact"

According to 21 CFR §175.300 the product can be used as resinous and polymeric coating

The formulation is in compliance with European Plastics Regulation No 10/2011

Description
In general Lusin® Lub O 32 F can be used as lubricant or release agent in the packaging industry.

If the product is applied on a die, e. g. in blown film applications, it reduces the build up during production. Lusin® Lub O 32 F, applied to the outside surface of PET preforms significantly reduces scratches to the plastic surfaces occurring during transport and handling. The blocking of bottles during the transport using air conveyors can be reduced to an absolute minimum by means of coating the preforms or the final bottles with Lusin® Lub O 32 F.

Application
In terms of lubrication of the outside surface of PET preforms, Lusin® Lub O 32 F should be applied using a suitable spray equipment, e.g. Steidle equipment.

The product is also suitable as a release agent in the thermoplastic processing industry. Mould temperatures should not exceed 200°C in terms of injection moulding. For film applications the die temperature should not exceed 190°C.

Lusin® Lub O 32 F is a waterless system. Therefore we strongly advise against dilution with water since even small impurities of water in the machinery and especially in the tubes will cause agglomerates that may block the system.

General Information
Agency Ratings	FDA 21 CFR 175.300 FDA 21 CFR 178.3570 Europe No 10/2011
Appearance	Yellow
Forms	Liquid

Physical	Nominal Value	Unit
Density	0.980 - 1.020	g/cm³
Viscosity	120 - 170	mPa·s

Resin Grade	Manufacturer	Category	Trademark
SHIN-A SE-140M70	SHIN-A T&C	Epoxy	SHIN-A
Tecopet® PT70 GR30 NL100 XA20	Eurotec Engineering Plastics	PET	Tecopet®
CompaDur® 121 GF 30 natural (005)	DimeLika Plast GmbH	PBT	CompaDur®
Sylvin 6246-85 Black	Sylvin Technologies Incorporated	PVC, Unspecified	Sylvin
Moplen HP525J	PolyMirae	PP Homopolymer	Moplen