Plaskon SMT-B-1RC Datasheet,Epoxy,Cookson Electronics - Semiconductor Products-SHANGHAI SUSHENG

Message
This material is an epoxy molding compound optimized specifically for PBGA applications. It is a fast cure molding compound for automold applications. It has the same unique resin system as the SMT-B-1, which minimizes warpage and enables trouble-free molding onto rigid and flexible laminate substrates. Minimal dimensional change after molding, post bake and subsequent solder treatment make this compound an excellent choice for PBGA applications.

General Information
Features	Semi-conductive Good dimensional stability Low warpage Low viscosity Fast curing
Uses	Application in Automobile Field
Forms	Liquid
Processing Method	Resin transfer molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.88	g/cm³	ASTM D792
Molding Shrinkage - Flow	0.050	%	ASTM D955

Mechanical	Nominal Value	Unit	Test Method
Flexural Modulus			ASTM D790
22°C	1.28	MPa	ASTM D790
215°C	0.588	MPa	ASTM D790
Flexural Strength			ASTM D790
22°C	0.00971	MPa	ASTM D790
215°C	0.00402	MPa	ASTM D790

Thermal	Nominal Value	Unit	Test Method
Glass Transition Temperature	226	°C	ASTM E1356
CLTE - Flow	1.5E-5	cm/cm/°C	ASTM D696
Thermal Conductivity	0.80	W/m/K	ASTM C177

Electrical	Nominal Value	Unit	Test Method
Volume Resistivity	2.0E+16	ohms·cm	ASTM D257
Dielectric Strength	28	kV/mm	ASTM D149
Dielectric Constant (1 kHz)	3.90		ASTM D150
Dissipation Factor (1 kHz)	4.0E-3		ASTM D150

Flammability	Nominal Value	Unit	Test Method
Flame Rating (3.18 mm)	V-0		UL 94
Oxygen Index	32	%	ASTM D2863

Additional Information
Recommended Storage Temperature: <5°CLife @ 5°C, defined as not more than 40% loss of spiral flow based on original values.: 24 monthsLife @ 21°C, defined as not more than 40% loss of spiral flow based on original values.: 5 daysLife @ 35°C, defined as not more than 40% loss of spiral flow based on original values.: 2 daysSpiral Flow, 175°C, 1000 psi: 105 cmAutomatic Orifice Viscosity, 175°C: 55 poiseRam Follower Gel Time, 175°C, 1000 psi: 12 secAsh Content: 78 %Hydrolyzable Halides: <1 ppmCull Hot Hardness, Shore D, 75 sec, 175°C: 86Volume Resistivity, 22°C: 2e16 ohm-cmAll test specimens are transfer molded and post cured for 4 hours at 175°C Linear Thermal Expansion, Alpha 1: 15 cm^-6/cm/°C Linear Thermal Expansion, Alpha 2: 55 cm^-6/cm/°C

Additional Information

Recommended Storage Temperature: <5°CLife @ 5°C, defined as not more than 40% loss of spiral flow based on original values.: 24 monthsLife @ 21°C, defined as not more than 40% loss of spiral flow based on original values.: 5 daysLife @ 35°C, defined as not more than 40% loss of spiral flow based on original values.: 2 daysSpiral Flow, 175°C, 1000 psi: 105 cmAutomatic Orifice Viscosity, 175°C: 55 poiseRam Follower Gel Time, 175°C, 1000 psi: 12 secAsh Content: 78 %Hydrolyzable Halides: <1 ppmCull Hot Hardness, Shore D, 75 sec, 175°C: 86Volume Resistivity, 22°C: 2e16 ohm-cmAll test specimens are transfer molded and post cured for 4 hours at 175°C Linear Thermal Expansion, Alpha 1: 15 cm^-6/cm/°C Linear Thermal Expansion, Alpha 2: 55 cm^-6/cm/°C

Injection instructions
Resin Transfer Molding: Preheat Temperature: 85 to 98°C Molding Temperature: 175°C Molding Pressure: 800 to 1200 psi Cycle Time, 175°C: 60 to 150 sec Post Mold Cure Time, 175°C: 0 to 4 hr

Resin Grade	Manufacturer	Category	Trademark
RJM SB302	RJM International, Inc.	PBT	RJM
Yuyao PBT 516	Yuyao Tenglong Plastics Co., Ltd.	PBT	Yuyao PBT
3M™ Dyneon™ Fluoroplastic ET 6218Z	3M Advanced Materials Division	ETFE	3M™ Dyneon™ Fluoroplastic
Karina IVORY PVC COMPOUND 70900-35/1-F-AC-LMP	Karina Ind. e Com. de Plásticos Ltda	PVC, Unspecified	Karina
TPX® MX004XB	Mitsui Chemicals, Inc.	PMP Copolymer	TPX®

Category:	Epoxy , Epoxy; Epoxide
Manufacturer:	Cookson Electronics - Semiconductor Products
Trademark:	Plaskon
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	cQ234n_Plaskon-SMT-B-1RC.pdf
PRICE:	Order Products email sales@su-jiao.com