Dynaflex™ G7670-9 (Black) Datasheet,TPE,PolyOne Corporation-SHANGHAI SUSHENG

Message
Dynaflex™G7670-9 (Black) is an easy-to-process universal TPE designed for a wide range of applications, including applications that must comply with FDA standards. It can be bonded to polypropylene by overlapping molding Similar to rubber Soft to the touch

General Information
Features	Workability, good Good processing stability Good liquidity General
Uses	overmolding Washer Soft touch application Soft handle Sporting goods General Consumer goods application field Grind cleaning materials
Agency Ratings	FDA 21 CFR 177.1210 2
RoHS Compliance	RoHS compliance
Appearance	Black
Forms	Particle
Processing Method	Extrusion Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.18	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)	21	g/10 min	ASTM D1238
Molding Shrinkage - Flow	0.60 - 1.4	%	ASTM D955

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A, 10 sec)	68		ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress ¹			ASTM D412
100% strain, 23°C ²	2.79	MPa	ASTM D412
300% strain, 23°C ³	3.24	MPa	ASTM D412
Tensile Strength (Break, 23°C)	6.79	MPa	ASTM D412
Tensile Elongation (Break, 23°C)	720	%	ASTM D412
Tear Strength	29.8	kN/m	ASTM D624
Compression Set (23°C, 22 hr)	19	%	ASTM D395B

Fill Analysis	Nominal Value	Unit	Test Method
Apparent Viscosity			ASTM D3835
200°C, 1340 sec^-1	40.1	Pa·s	ASTM D3835
200°C, 11200 sec^-1	8.80	Pa·s	ASTM D3835

Injection	Nominal Value	Unit
Suggested Max Regrind	20	%
Rear Temperature	166 - 177	°C
Middle Temperature	177 - 193	°C
Front Temperature	188 - 227	°C
Nozzle Temperature	193 - 227	°C
Mold Temperature	15.6 - 37.8	°C
Back Pressure	0.00 - 0.827	MPa
Screw Speed	40 - 100	rpm

Injection instructions
在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Dynaflex™ G7670-9（黑色）可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Dynaflex™ G7670-9（黑色）具有极好的熔体稳定性。最长停留时间可能会根据机筒尺寸有所变化。通常，如果机器闲置 8 - 10 分钟或以上，则应将机筒排空。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：350 - 900 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：2 - 10 秒保持时间（薄部件）：1 - 3 秒

Injection instructions

在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Dynaflex™ G7670-9（黑色）可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Dynaflex™ G7670-9（黑色）具有极好的熔体稳定性。最长停留时间可能会根据机筒尺寸有所变化。通常，如果机器闲置 8 - 10 分钟或以上，则应将机筒排空。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：350 - 900 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：2 - 10 秒保持时间（薄部件）：1 - 3 秒

Note Message
1 .	2 hours
2 .	Mouth die c
3 .	C mould

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	PolyOne Corporation
Trademark:	Dynaflex™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	bZIVky_Dynaflex-G7670-9-Black-.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
CALIBRE™ 303V-10	Trinseo	PC	CALIBRE™
EUROPLEX® Sheet F6	Evonik Industries AG	PC	EUROPLEX® Sheet
Geon™ HTX Ultra LA426G Black 2880	PolyOne Corporation	PVC Alloy	Geon™ HTX Ultra
HAIPLEN H30 G3	Taro Plast S.p.A.	PP Homopolymer	HAIPLEN
POLYfill PPH GF8020 PB	Polykemi AB	PP Homopolymer	POLYfill