Sarlink® TPE AB-2233D Datasheet,TPE,Teknor Apex Company-SHANGHAI SUSHENG

Message
Sarlink®TPE AB-2233D is a thermoplastic elastomer (TPE) material,. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific. The processing methods are: blow molding, extrusion or injection molding. Typical application areas include: Automotive Industry engineering/industrial accessories

General Information
Uses	Blow molding applications Washer Weather-resistant sealing strip Application in Automobile Field Car interior parts Automotive exterior parts Car exterior decoration General
Appearance	Translucent
Forms	Particle
Processing Method	Blow molding Extrusion Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	0.898	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)	12	g/10 min	ASTM D1238
Molding Shrinkage			ASTM D955
Flow	0.90	%	ASTM D955
Flow : 80°C, 30 minutes	0.90	%	ASTM D955
Flow : 93°C, 30 minutes	1.2	%	ASTM D955
Transverse flow	1.0	%	ASTM D955
Transverse flow : 80°C	0.90	%	ASTM D955
Transverse flow : 93°C	1.3	%	ASTM D955

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore D, 10 sec)	33		ASTM D2240

Mechanical	Nominal Value	Unit	Test Method
Flexural Modulus	138	MPa	ASTM D790

Elastomers	Nominal Value	Unit	Test Method
Tensile Strength (Yield)	8.41	MPa	ASTM D412
Tensile Elongation (Break)	570	%	ASTM D412
Tear Strength ¹	61.3	kN/m	ASTM D624

Aging	Nominal Value	Unit	Test Method
Change in Tensile Strength in Air			ASTM D573
90°C, 1000 hr	-6.0	%	ASTM D573
Transverse flow : 100°C, 1008 hr	4.6	%	ASTM D573
Flow : 100°C, 1008 hr	8.0	%	ASTM D573
107°C, 400 hr	-4.0	%	ASTM D573
Change in Ultimate Elongation in Air			ASTM D573
90°C, 1000 hr	-23	%	ASTM D573
Transverse flow : 100°C, 1008 hr	-18	%	ASTM D573
Flow : 100°C, 1008 hr	-7.6	%	ASTM D573
107°C, 400 hr	-25	%	ASTM D573

Thermal	Nominal Value	Unit	Test Method
Brittleness Temperature	-60.0	°C	ASTM D746
Thermal Conductivity	0.16	W/m/K	ASTM C177

Flammability	Nominal Value	Unit	Test Method
Burning Rate	25	mm/min	ISO 3795

Fill Analysis	Nominal Value	Unit	Test Method
Melt Density	0.785	g/cm³
Melt Specific Heat	2590	J/kg/°C	ASTM C351
Melt Thermal Conductivity	0.16	W/m/K	ASTM C177
No Flow Temperature	125	°C

Additional Information
雾化，SAE-J1756，6小时，95°C：72撕裂强度ASTM D624试验中所列的数值，依照ASTM D1004进行试验。重量变化，空气老化，1000小时，90°C：-0.7 %重量变化，空气老化，400 小时，107°C：-0.5 %熔体导热性，ASTM C177，205°C：0.159 W/m/K模具收缩，线性变换，ASTM D955：0.01英寸/英寸模具收缩，线性变换，ASTM D955，0.5小时，80°C：0.009英寸/英寸模具收缩，线性变换，ASTM D955，0.5小时，93°C：0.013英寸/英寸可燃性燃烧速率，FMVSS 302，最大100，1.00英寸/分钟：合格

Additional Information

雾化，SAE-J1756，6小时，95°C：72撕裂强度ASTM D624试验中所列的数值，依照ASTM D1004进行试验。重量变化，空气老化，1000小时，90°C：-0.7 %重量变化，空气老化，400 小时，107°C：-0.5 %熔体导热性，ASTM C177，205°C：0.159 W/m/K模具收缩，线性变换，ASTM D955：0.01英寸/英寸模具收缩，线性变换，ASTM D955，0.5小时，80°C：0.009英寸/英寸模具收缩，线性变换，ASTM D955，0.5小时，93°C：0.013英寸/英寸可燃性燃烧速率，FMVSS 302，最大100，1.00英寸/分钟：合格

Injection	Nominal Value	Unit
Rear Temperature	199 - 210	°C
Middle Temperature	204 - 216	°C
Front Temperature	210 - 221	°C
Nozzle Temperature	216 - 227	°C
Processing (Melt) Temp	216 - 227	°C
Mold Temperature	35.0 - 65.6	°C
Injection Pressure	1.38 - 6.89	MPa
Injection Rate	Fast
Back Pressure	0.172 - 0.862	MPa
Screw Speed	50 - 120	rpm
Cushion	3.81 - 25.4	mm

Injection instructions
无需干燥。但如果湿度过大，则将粒料在150°F (65°C)的温度下干燥2-4小时。

Extrusion	Nominal Value	Unit
Cylinder Zone 1 Temp.	193 - 204	°C
Cylinder Zone 2 Temp.	199 - 210	°C
Cylinder Zone 3 Temp.	204 - 216	°C
Cylinder Zone 5 Temp.	210 - 221	°C
Die Temperature	216 - 227	°C

Extrusion instructions
螺杆转速30 - 100 rpm

Note Message
1 .	C mould

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	Teknor Apex Company
Trademark:	Sarlink® TPE
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	aeup75_Sarlink-TPE-AB-2233D.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Radilon® A RV350	Radici Plastics	Nylon 66	Radilon®
Tarnamid® T-27 GF 30	Grupa Azoty S.A.	Nylon 6	Tarnamid®
NEXUS PP HPP20	Nexus Resin Group, LLC.	PP Homopolymer	NEXUS PP
Cawiton® CN970	Wittenburg B.V.	SEBS	Cawiton®
Hostalen GC 7260	LyondellBasell Industries	HDPE	Hostalen