Order Products : sales@su-jiao.com
CERTENE™ PHF-4
| Category: | PP, HMS , High Melt Strength Polypropylene |
| Manufacturer: | Muehlstein |
| Trademark: | CERTENE™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | aEUgVF_CERTENE-PHF-4.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| PHF-4 is a certified prime grade Polypropylene specially designed for extrusion of profile and cast film applications. PHF-4 combines excellent processability and high degree of thermal stabilization, with good melt strength, high tensile strength and good fibrillation tendency. PHF-4 applications include stretched tapes, drinking straws, monofilament yarns for rope, fibrillated tape for twine, and flat films. PHF-4 recommended processing temperature is between 210° to 230°C. PHF-4 complies with FDA regulation 21CFR 177.1520 and with most international regulations concerning the use of Polypropylene in contact with food. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 0.903 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (230°C/2.16 kg) | 4.0 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 91 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength 1(Yield, Injection Molded) | 35.2 | MPa | ASTM D638 |
| Tensile Elongation 2(Yield, Injection Molded) | 11 | % | ASTM D638 |
| Flexural Modulus - 1% Secant 3(Injection Molded) | 1720 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact (23°C, Injection Molded) | 43 | J/m | ASTM D256 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load (0.45 MPa, Unannealed, Injection Molded) | 98.0 | °C | ASTM D648 |
| Vicat Softening Temperature | 151 | °C | ASTM D1525 |
| Additional Information |
|---|
| All specimens were injection molded according to ASTM D2146 Type 1. |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 98.9 - 110 | °C |
| Note Message | |
|---|---|
| 1 . | 50 mm/min |
| 2 . | 50 mm/min |
| 3 . | 1.3 mm/min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| UNISOFT TPE™ ST-75A-NT-1-01 | UNITED SOFT PLASTICS, Inc. | SEBS | UNISOFT TPE™ |
| Evoprene™ LF 6152 | AlphaGary | SBC | Evoprene™ LF |
| Alathon® M5370P | LyondellBasell Industries | HDPE | Alathon® |
| Hyflon® MFA® P6022 | Solvay Specialty Polymers | Perfluoropolymer | Hyflon® MFA® |
| TECHNYL® C 246 NATURAL | Solvay Engineering Plastics | Nylon 6 | TECHNYL® |
