Order Products : sales@su-jiao.com
KRATON® D1161 K
| Category: | SIS , Styrene Isoprene Styrene Block Copolymer |
| Manufacturer: | Kraton Polymers LLC |
| Trademark: | KRATON® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | ZEgW6W_KRATON-D1161-K.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
Kraton D1161 K is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied from North America in the physical form identified below.
Kraton D1161 K is used as an ingredient in formulating adhesives, sealants and coatings. It may also find use as a modifier of bitumen or thermoplastics and in compound formulations. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Appearance |
|
| Forms |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 0.920 | g/cm³ | ASTM D4025 |
| Melt Mass-Flow Rate (MFR) (200°C/5.0 kg) | 12 | g/10 min | |
| Bound Styrene | 14.0 to 17.0 | % | Internal Method |
| Antioxidant Additive | 0.080 to 0.30 | % | Internal Method |
| Ash Content - T, Talc | 0.25 to 0.45 | % | Internal Method |
| Total Extractables | < 1.0 | % | Internal Method |
| Viscosity 1(25°C) | 1.20 | Pa·s | Internal Method |
| Volatile Matter | < 0.70 | % | Internal Method |
| Additional Information | Nominal Value | ||
|---|---|---|---|
| Diblock Content | 19.0 | ||
| Styrene/Rubber ratio | 15/85 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 10 sec, Compression Molded) | 32 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress 2(300% Strain) | 0.689 | MPa | ASTM D412 |
| Tensile Strength 3(Yield) | 21.4 | MPa | ASTM D412 |
| Tensile Elongation 4(Break) | 1300 | % | ASTM D412 |
| Note Message | |
|---|---|
| 1 . | 25% in toluene solution |
| 2 . | Typical properties determined on film cast from toluene solution. |
| 3 . | Typical properties determined on film cast from toluene solution. |
| 4 . | Typical properties determined on film cast from toluene solution. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Tecomid® NB40 GR30 NL | Eurotec Engineering Plastics | Nylon 6 | Tecomid® |
| 4MID® 9A13100 | 4Plas | Nylon 66 | 4MID® |
| GLS PP MH1 | GLS Polymers Pvt. Ltd. | PP, Unspecified | GLS PP |
| LEXAN™ HFD1014 resin | SABIC Innovative Plastics | PC | LEXAN™ |
| LNP™ LUBRICOMP™ IFL36 compound | SABIC Innovative Plastics | Nylon 612 | LNP™ LUBRICOMP™ |
