Dynalloy™ OBC 8100-N65 Datasheet,TPE,PolyOne Corporation-SHANGHAI SUSHENG

Message
DYNALLOY™OBC8100-N65 is a kind of using Dow INFUSE™TPE material with unique characteristics of olefin block polymer. 8100 series of materials are specially developed for TPE applications that require direct contact with food. New Products. Commercial norms have not yet been established. can be bonded to polypropylene direct contact with food strong liquidity Excellent coloring

General Information
Features	Good liquidity Good coloring Compliance of Food Exposure
Uses	overmolding Kitchen utensils Non-specific food applications Household goods Soft touch application Food service sector
Agency Ratings	BfR food contact, not rated 2 FDA 21 CFR 177.2600 3 European 2002/72/EC 4
RoHS Compliance	RoHS compliance
Appearance	Natural color
Forms	Particle
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.06	g/cm³	ASTM D792

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A, 10 sec)	63		ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress ¹			ASTM D412
100% strain, 23°C ²	3.00	MPa	ASTM D412
300% strain, 23°C ³	3.65	MPa	ASTM D412
Tensile Strength (Break, 23°C)	4.27	MPa	ASTM D412
Tensile Elongation (Break, 23°C)	570	%	ASTM D412
Tear Strength	23.6	kN/m	ASTM D624
Compression Set (23°C, 22 hr)	21	%	ASTM D395B

Fill Analysis	Nominal Value	Unit	Test Method
Apparent Viscosity			ASTM D3835
200°C, 1340 sec^-1	117	Pa·s	ASTM D3835
200°C, 11200 sec^-1	27.0	Pa·s	ASTM D3835

Injection	Nominal Value	Unit
Rear Temperature	160 - 188	°C
Middle Temperature	177 - 193	°C
Front Temperature	182 - 210	°C
Nozzle Temperature	193 - 216	°C
Mold Temperature	15.6 - 26.7	°C
Back Pressure	0.00 - 0.689	MPa
Screw Speed	25 - 100	rpm

Injection instructions
以聚丙烯 (PP)、乙烯醋酸乙烯共聚物 (EVA) 或低密度聚乙烯 (PE) 为基础的色母料最适合 DYNALLOY™ OBC 8100-N65 着色。使用熔体流动速率较高（范围为 25 - 40 克/10 分钟）的色母料，则能达到较好的颜色分散效果。典型的色母料用量为 1% 至 5%（重量）。不应采用以 PVC 为基础的色母料。色母料是否适用，应由用户通过试验来最终确定。在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：175 - 800 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：3 - 10 秒保持时间（薄部件）：1 - 3 秒

Injection instructions

以聚丙烯 (PP)、乙烯醋酸乙烯共聚物 (EVA) 或低密度聚乙烯 (PE) 为基础的色母料最适合 DYNALLOY™ OBC 8100-N65 着色。使用熔体流动速率较高（范围为 25 - 40 克/10 分钟）的色母料，则能达到较好的颜色分散效果。典型的色母料用量为 1% 至 5%（重量）。不应采用以 PVC 为基础的色母料。色母料是否适用，应由用户通过试验来最终确定。在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：175 - 800 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：3 - 10 秒保持时间（薄部件）：1 - 3 秒

Note Message
1 .	2 hours
2 .	Mouth die c
3 .	C mould

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	PolyOne Corporation
Trademark:	Dynalloy™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	Z6Vg9A_Dynalloy-OBC-8100-N65.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Rilsamid® AECNO TL	Arkema	Nylon 12	Rilsamid®
ECOGRAN® ABSI F20 BLK	Eurocompound Polymers	ABS	ECOGRAN®
LEXAN™ EXL1112 resin	SABIC Innovative Plastics	PC	LEXAN™
Karina BLACK PVC COMPOUND -E 75900-48/ 1-C-IS	Karina Ind. e Com. de Plásticos Ltda	PVC, Unspecified	Karina
Karina BLACK COLOR CONCENTRATE 48/1-FC-6 (***)	Karina Ind. e Com. de Plásticos Ltda	PVC, Unspecified	Karina