Order Products : sales@su-jiao.com
Celanex® 6500
| Category: | PBT , Polybutylene Terephthalate |
| Manufacturer: | Celanese Corporation |
| Trademark: | Celanex® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | YKdXfL_Celanex-6500.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| Celanex 6500 is a 30% glass/mineral polyester with improved surface finish and a good balance of mechanical properties and processability. |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Features |
|
| RoHS Compliance |
|
| Multi-Point Data |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.55 | g/cm³ | ASTM D792, ISO 1183 |
| Melt Mass-Flow Rate (MFR) | 22 | g/10 min | ASTM D1238 |
| Molding Shrinkage | |||
| Flow | 0.20 - 0.50 | % | ASTM D955 |
| Vertical flow direction | 0.50 - 0.80 | % | ISO 294-4 |
| Flow direction | 0.0 - 0.50 | % | ISO 294-4 |
| Water Absorption (Equilibrium, 23°C, 50% RH) | 0.19 | % | ISO 62 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (M-Scale) | 89 | ISO 2039-2 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | 9700 | MPa | ISO 527-2/1A/1 |
| Tensile Strength | |||
| Fracture, 23°C | 110 | MPa | ASTM D638 |
| Fracture | 125 | MPa | ISO 527-2/1A/5 |
| Tensile Elongation | |||
| Fracture, 23°C | 3.0 | % | ASTM D638 |
| Fracture | 2.2 | % | ISO 527-2/1A/5 |
| Flexural Modulus (23°C) | 9500 | MPa | ISO 178 |
| Flexural Stress (23°C) | 180 | MPa | ISO 178 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30°C | 6.4 | kJ/m² | ISO 179/1eA |
| 23°C | 7.1 | kJ/m² | ISO 179/1eA |
| Charpy Unnotched Impact Strength | ISO 179/1eU | ||
| -30°C | 30 | kJ/m² | ISO 179/1eU |
| 23°C | 30 | kJ/m² | ISO 179/1eU |
| Notched Izod Impact (23°C) | 5.3 | kJ/m² | ISO 180/1A |
| Unnotched Izod Impact Strength (23°C) | 31 | kJ/m² | ISO 180/1U |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Deflection Temperature | |||
| 0.45 MPa, not annealed | 223 | °C | ISO 75-2/B |
| 0.45 MPa, annealed | 220 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 204 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 202 | °C | ISO 75-2/A |
| Glass Transition Temperature 1 | 54.0 | °C | ISO 11357-2 |
| Melting Temperature 2 | 225 | °C | ISO 11357-3, ASTM D3418 |
| Linear thermal expansion coefficient | ISO 11359-2 | ||
| Flow | 2.8E-5 | cm/cm/°C | ISO 11359-2 |
| Lateral | 8.5E-5 | cm/cm/°C | ISO 11359-2 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Surface Resistivity | 3.0E+16 | ohms | IEC 60093 |
| Volume Resistivity | |||
| -- | 2.0E+14 | ohms·cm | ASTM D257 |
| -- | 2.0E+16 | ohms·cm | IEC 60093 |
| Dielectric Strength | |||
| -- 3 | 24 | kV/mm | ASTM D149 |
| -- | 22 | kV/mm | IEC 60243-1 |
| Dielectric Constant | |||
| 1 MHz | 4.20 | ASTM D150 | |
| 100 Hz | 3.50 | IEC 60250 | |
| 1 MHz | 3.80 | IEC 60250 | |
| Dissipation Factor | |||
| 1 MHz | 0.020 | ASTM D150 | |
| 1 MHz | 0.040 | IEC 60250 | |
| Arc Resistance | 124 | sec | ASTM D495 |
| Comparative Tracking Index | 325 | V | IEC 60112 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating | HB | UL 94 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 120 - 130 | °C | |
| Drying Time | 4.0 | hr | |
| Suggested Max Moisture | 0.020 | % | |
| Suggested Max Regrind | 25 | % | |
| Hopper Temperature | 20.0 - 50.0 | °C | |
| Rear Temperature | 230 - 250 | °C | |
| Middle Temperature | 235 - 255 | °C | |
| Front Temperature | 235 - 255 | °C | |
| Nozzle Temperature | 240 - 265 | °C | |
| Processing (Melt) Temp | 235 - 265 | °C | |
| Mold Temperature | 65.0 - 96.0 | °C | |
| Injection Rate | Moderate-Fast | ||
| Back Pressure | 0.00 - 0.345 | MPa |
| Injection instructions |
|---|
| Manifold Temperature: 250 to 265°CZone 4 Temperature: 240 to 265°CFeed Temperature: 230 to 250°C |
| Note Message | |
|---|---|
| 1 . | 10°C/min |
| 2 . | 10°C/min |
| 3 . | Method A (short time) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Multi-Flex® TPE A6221 CUV | Multibase, A Dow Corning Company | TPE | Multi-Flex® TPE |
| ExTima™ GP MB PC 330 | Ovation Polymers Inc. | PC | ExTima™ |
| Lucky Enpla LHLD1030 | Lucky Enpla Co LTD | PC | Lucky Enpla |
| Pearlthane® ECO D12T90 | Lubrizol Advanced Materials, Inc. | TPU, Unspecified | Pearlthane® ECO |
| PERLER® N09X4002B01 | A.D. Compound S.p.A. | PP Homopolymer | PERLER® |
