Tecnoflon® TN 50A

Category:	Fluorelastomer , Fluoroelastomer
Manufacturer:	Solvay Specialty Polymers
Trademark:	Tecnoflon®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	Xf7fPc_Tecnoflon-TN-50A.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
TECNOFLON® TN 50A is a medium-low viscosity fluoroelastomer terpolymer. It does not contain curatives, therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve required properties. Thanks to its 68% of fluorine content, a good compromise between chemical resistance and compression set value is obtained. The careful distribution of molecular weights and medium-low viscosity maximize its performance in applications such as injection molding or extrusion where rheological properties are critical. Some of the basic properties of Tecnoflon® TN 50A are: Very good mold flow Superior mold release Good compression set Good extrusion behavior Tecnoflon® TN 50A can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® TN 50A can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

Message

TECNOFLON® TN 50A is a medium-low viscosity fluoroelastomer terpolymer. It does not contain curatives, therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve required properties. Thanks to its 68% of fluorine content, a good compromise between chemical resistance and compression set value is obtained. The careful distribution of molecular weights and medium-low viscosity maximize its performance in applications such as injection molding or extrusion where rheological properties are critical.

Some of the basic properties of Tecnoflon® TN 50A are:

Very good mold flow

Superior mold release

Good compression set

Good extrusion behavior

Tecnoflon® TN 50A can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers.
Tecnoflon® TN 50A can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

General Information
Features	Good Chemical Resistance Good Flow Good Mold Release Low Compression Set Medium-low Viscosity Terpolymer
Uses	Belts/Belt Repair Blending Gaskets Hose Profiles Seals Sheet Valves/Valve Parts
Appearance	Translucent
Forms	Slab
Processing Method	Calendering Compounding Compression Molding Extrusion Injection Molding Resin Transfer Molding

Physical	Nominal Value	Unit
Mooney Viscosity ¹(ML 1+10, 121°C)	23	MU
Fluorine Content ²	68	%

Note Message
1 .	Raw polymer
2 .	Raw polymer

Resin Grade	Manufacturer	Category	Trademark
Makrolon® 3156	Covestro - Polycarbonates	PC	Makrolon®
Next Nylon 6 Prime Series NGIM30-01BK	Next Polymers Ltd.	Nylon 6	Next Nylon 6 Prime Series
KRATON® D1171 P	Kraton Polymers LLC	SIS	KRATON®
Latimass 62-07 D025	LATI S.p.A.	Nylon 6	Latimass
Hostacom CR 1171 G1 C12541	LyondellBasell Industries	PP Copolymer	Hostacom