Order Products : sales@su-jiao.com
tefabloc® TP SD 310 40A
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Mitsubishi Chemical Performance Polymers, Inc. |
| Trademark: | tefabloc® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | VGA5Sf_tefabloc-TP-SD-310-40A.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
tefabloc®TP SD 310 40A is a thermoplastic elastomer (TPE) material,. This product is available in North America or Europe. The processing method is injection molding. tefabloc®The main features of TP SD 310 40A are:
Typical application areas include:
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Resin ID (ISO 1043) |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.04 | g/cm³ | ISO 1183 |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 32 | g/10 min | ISO 1133 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 15 sec, Injection Molded) | 40 | ISO 868 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Abrasion | 390 | mm³ | DIN 53516 |
| Aging | Nominal Value | Unit | |
|---|---|---|---|
| Resistance to Aging | 125 | °C |
| Thermal | Nominal Value | Unit | |
|---|---|---|---|
| Service Temperature | -50 - 70 | °C |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ISO 37 | ||
| 20% strain | 0.600 | MPa | ISO 37 |
| 100% strain | 1.10 | MPa | ISO 37 |
| Tensile Stress (Break) | 3.00 | MPa | ISO 37 |
| Tensile Elongation (Break) | 760 | % | ISO 37 |
| Tear Strength 1 | 16 | kN/m | ISO 34-1 |
| Compression Set 2(23°C, 72 hr) | 25 | % | ISO 815 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Rear Temperature | 160 | °C | |
| Middle Temperature | 170 | °C | |
| Front Temperature | 180 | °C | |
| Injection Rate | Moderate | ||
| Screw Compression Ratio | 2.5:1.0 - 3.0:1.0 |
| Injection instructions |
|---|
| Screw Speed: Medium |
| Note Message | |
|---|---|
| 1 . | Method B, right-angle specimen (without cut) |
| 2 . | Type B |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Maxiglas® MG515 | Maxiglas Corporation | Acrylic (PMMA) | Maxiglas® |
| Reblend® B4070 NATURALE | SO.F.TER. SPA | PC+ABS | Reblend® |
| Sylvin 8891-92 Black | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
| Colorite 66 Series 7066 | Colorite Polymers | PVC, Unspecified | Colorite 66 Series |
| Ensinger HYDLAR® Z | Ensinger Inc. | Nylon 66 | Ensinger |
