Order Products : sales@su-jiao.com
ETILINAS BPD 4045
| Category: | HDPE , High Density Polyethylene |
| Manufacturer: | POLYETHYLENE MALAYSIA SDN BHD |
| Trademark: | ETILINAS |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | UW337p_ETILINAS-BPD-4045.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| ETILINAS BPD 4045 is designed specifically for the jacketing of communication and power cables. It is also recommended for insulation of low voltage aerial cables. It is based on a special high density copolymer with excellent resistance to environmental stress cracking, abrasion, weather and heat deformation. It meets the applicable requirements as below when processed using sound extrusion practice and testing procedure: IEC 60502, ST7; IEC 840; IEC 708; ASTM D1248, Type III, Class C, 5, Grade W8; BS6234: H03C, TS2. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Appearance |
|
| Forms |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.941 | g/cm³ | ISO 1183 |
| Melt Mass-Flow Rate (MFR) | ISO 1133 | ||
| 190°C/2.16 kg | 0.20 | g/10 min | ISO 1133 |
| 190°C/5.0 kg | 0.85 | g/10 min | ISO 1133 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore D) | 62 | ISO 868 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flexural Modulus | 850 | MPa | ISO 178 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | -100 | °C | ASTM D746 |
| Vicat Softening Temperature | 120 | °C | ISO 306/A |
| CLTE - Flow (20 to 60°C) | 1.5E-4 | cm/cm/°C | ASTM D696 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric Strength | 20 | kV/mm | IEC 60243-1 |
| Dielectric Constant (1 MHz) | 2.60 | IEC 60250 | |
| Dissipation Factor (1 MHz) | 1.0E-3 | IEC 60250 |
| Additional Information |
|---|
| Density of Base Resin , ISO 1183: 941 kg/m³Density of Compound, ISO 1183: 952 kg/m³Carbon Black Content, ISO 6964: 2.5%Tensile Stress at Yield, IEC 811-1-1: 23 MPaElongation at Break, IEC 811-1-1: >600%Thermal Conductivity, BS 874, 23°C: 0.4 W/m/°COxidation Induction Time, ISO TR10837, 210°C: >20 minEnvironmental Stress Crack Resistance, IEC 811-4-1, F0: >1000 hr |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Melt Temperature | 210 - 235 | °C |
| Extrusion instructions |
|---|
| Suggested Screen Pack: 40/80 Mesh |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Glastherm® HT | Glastic Corporation | Polyester, TS | Glastherm® |
| EPO-TEK® H61 | Epoxy Technology Inc. | Epoxy | EPO-TEK® |
| Petlon Prime A2-G15-00-BK | Petlon Polymers Ltd | Nylon 66 | Petlon Prime |
| Pinnacle PP 4220H | Pinnacle Polymers | PP Impact Copolymer | Pinnacle PP |
| Polifor® L6 GF/30 NATURALE | SO.F.TER. SPA | PP Homopolymer | Polifor® |
