Order Products : sales@su-jiao.com
MAGNUM™ 357 HP
| Category: | ABS , ABS Resin |
| Manufacturer: | Trinseo |
| Trademark: | MAGNUM™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | UEf9VL_MAGNUM-357-HP.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
MAGNUM ABS resins are thermoplastic materials which provide an excellent balance of processability, impact resistance and heat resistance as imparted by the various polymer compositions. MAGNUM ABS resins are available in a wide range of melt flow rates, impact strength and heat resistance for both high and low gloss applications manufactured by injection molding, sheet or profile extrusion and thermoforming processes. Automotive MAGNUM ABS resins offer a wide range of gloss, viscosity, impact strength and heat properties for use in numerous automotive applications. Melt flow rates from 1 to 12 g/10 min, impact strengths from 2.5 to 12 ft-lb/in and heat distortion temperatures from 165°F to 190°F are available. Available primarily as natural plus concentrates, MAGNUM ABS resins are used in a wide variety of automotive applications including structural instrument panels, consoles, pillars, and exterior trim parts requiring painting and plating. MAGNUM 357 HP ABS resin is a medium gloss, high heat material that has slightly higher heat resistance and a little higher melt flow rate than MAGNUM 358 HP ABS resin. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | |||
| -- | 1.06 | g/cm³ | ASTM D792 |
| -- | 1050 | kg/m³ | ISO 1183 1 |
| Melt Mass-Flow Rate (MFR) (230°C/3.8 kg) | 2.0 | g/10 min | ASTM D1238 |
| Melt volume-flow rate (220°C/10.0 kg) | 6.00 | cm³/10min | ISO 1133 2 |
| Molding Shrinkage - Flow | 0.40 to 0.70 | % | ASTM D955 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | |||
| -- 3 | 2000 | MPa | ASTM D638 |
| -- | 2100 | MPa | ISO 527-2 4 |
| Tensile Strength | |||
| Yield 5 | 37.9 | MPa | ASTM D638 |
| Yield | 40.0 | MPa | ISO 527-2 6 |
| Break 7 | 33.1 | MPa | ASTM D638 |
| Tensile Strain | |||
| Yield | 2.3 | % | ISO 527-2 8 |
| Break 9 | 45 | % | ASTM D638 |
| Nominal strain at break | 40 | % | ISO 527-2 10 |
| Flexural Modulus 11 | 2210 | MPa | ASTM D790 |
| Flexural Strength 12 | 62.1 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy notched impact strength | ISO 179/1eA 13 | ||
| -30°C | 7.00 | kJ/m² | |
| 23°C | 16.0 | kJ/m² | |
| Charpy impact strength | ISO 179/1eU 14 | ||
| -30°C | 80.0 | kJ/m² | |
| 23°C | No Break | ||
| Notched Izod Impact 15 | ASTM D256 | ||
| -18°C, 3.20 mm | 130 | J/m | |
| 23°C, 3.20 mm | 310 | J/m | |
| Instrumented Dart Impact 16 | ASTM D3763 | ||
| -18°C, 3.20 mm, Peak Energy | 22.6 | J | |
| -18°C, 3.20 mm, Total Energy | 23.7 | J | |
| 23°C, 3.20 mm, Peak Energy | 32.8 | J | |
| 23°C, 3.20 mm, Total Energy | 42.9 | J |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | |||
| 0.45 MPa, Unannealed, 3.20 mm | 104 | °C | ASTM D648 |
| 0.45 MPa | 104 | °C | ISO 75-2 17 |
| 1.8 MPa, Unannealed, 3.20 mm | 87.8 | °C | ASTM D648 |
| 1.8 MPa | 90.0 | °C | ISO 75-2 18 |
| Vicat Softening Temperature | |||
| -- | 120 | °C | ASTM D1525 |
| 50°C/h, B (50N) | 109 | °C | ISO 306 19 |
| CLTE - Flow | |||
| -- | 8.1E-5 | cm/cm/°C | ASTM D696 |
| -- | 8.0E-5 | cm/cm/°C | ISO 11359-2 20 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melt Density | 1.08 | g/cm³ | |
| Melt Specific Heat | 1890 | J/kg/°C | ASTM C351 |
| Melt Thermal Conductivity | 0.13 | W/m/K | ASTM C177 |
| No Flow Temperature | 150 | °C | |
| Ejection Temperature | 127 | °C |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 82.2 to 85.0 | °C | |
| Drying Time | 2.0 to 4.0 | hr | |
| Suggested Max Moisture | 0.10 | % | |
| Processing (Melt) Temp | 260 to 282 | °C | |
| Mold Temperature | 37.8 to 82.2 | °C | |
| Back Pressure | 0.345 to 0.689 | MPa | |
| Clamp Tonnage | 2.8 to 4.1 | kN/cm² | |
| Screw L/D Ratio | 20.0:1.0 | ||
| Screw Compression Ratio | 1.5:1.0 to 3.5:1.0 |
| Note Message | |
|---|---|
| 1 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 2 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 3 . | Type I, 51 mm/min |
| 4 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 5 . | Type I, 51 mm/min |
| 6 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 7 . | Type I, 51 mm/min |
| 8 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 9 . | Type I, 51 mm/min |
| 10 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 11 . | Type I, 1.3 mm/min |
| 12 . | Type I, 1.3 mm/min |
| 13 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 14 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 15 . | 0.25 mm Notch Depth |
| 16 . | 3.39 m/sec |
| 17 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 18 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 19 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 20 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| TEKASTER™ F615G30 | Mando Advanced Materials Co., Ltd. | PET | TEKASTER™ |
| THERMOLAST® K TC6CSN (Series: CS) | KRAIBURG TPE | TPE | THERMOLAST® K |
| Toraypef® 30030 AP17 | Toray Resin Company | Polyolefin, Unspecified | Toraypef® |
| Fainplast PVC FKA 97 | Fainplast Compounds S.r.l | PVC, Unspecified | Fainplast PVC |
| Karina GRAY PVC COMPOUND 830-18/361-IS-RG-PO | Karina Ind. e Com. de Plásticos Ltda | PVC, Unspecified | Karina |
