Order Products : sales@su-jiao.com
Halar® 3404DA
| Category: | ECTFE , Ethylene Chlorotrifluoroethylene Copolymer |
| Manufacturer: | Solvay Specialty Polymers |
| Trademark: | Halar® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | UD1zTT_Halar-3404DA.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Halar®3404DA is a filled, pearl white, semi-crystalline, melt-processable fluororesin that fully meets the requirements of the Federal Food, Drug and Cosmetic Act Food Additives Regulation 21 CFR 177.1380 (a)(4). It is specially used for anti-static powder coating and can be used as primer, two primer or topcoat for protective and anti-corrosion products. Halar®3404DA is better at water vapor permeability than Halar®6014. At the same time, it has good chemical, electrical and thermal properties. In addition, Halar®3404DA coating also shows excellent surface finish and hardness. Halar®The main features of 3404DA include:
-Excellent thermal performance
-Outstanding surface characteristics
|
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.68 | g/cm³ | ASTM D3275 |
| Melt Mass-Flow Rate (MFR) (275°C/2.16 kg) | 2.0 | g/10 min | ASTM D3275 |
| Average Particle Size 1 | 28 | µm | Internal method |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melting Temperature | 242 | °C | ASTM D3275 |
| Additional Information |
|---|
| 加工-Halar®3404DA可以使用常规抗静电粉末涂料技术。一般包括基材准备、涂层、烘烤和冷却工序。根据用途的不同，会采用进一步的工序。可能会需要重复几遍，以获得所需的Halar®用量及涂层厚度。-Halar®3404DA可以单独使用，不需要进一步配混。基材准备、喷枪参数如电压、烘箱温度和时间必须控制好，以获得无瑕疵涂层产品。储存和操作 如果在室温下保持放置在干净干燥的环境， Halar®可熔融加工含氟聚合物树脂就无需担心保质期问题。打开的容器必须再次密封好，以防止污染。 安全性和毒理学-使用 Halar®可熔融加工含氟聚合物树脂前，应参阅产品的材料安全数据表单，遵循所有的标签说明和操作注意事项。-和所有含氟聚合物材料一样，操作和加工必须在通风良好的场所进行，设备上方应安装蒸汽抽气装置。不能吸入烟雾，应避免接触皮肤和眼睛。如有皮肤接触，用肥皂和水清洗干净。如触及眼睛，应立即用大量清水冲洗，并寻求医疗帮助。不要在粉尘、蒸汽或烟雾污染的环境吸烟。-废物处置详细建议请参考材料安全数据表单。包装-Halar®3404DA用一次性桶包装，每桶25公斤。每只桶内有两只聚乙烯树脂衬袋。 |
| Note Message | |
|---|---|
| 1 . | Method C |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| SABIC® PPcompound 8900 | Saudi Basic Industries Corporation (SABIC) | PP, Unspecified | SABIC® PPcompound |
| FHR EPS 55-6455 | Flint Hills Resources, LP | PS (EPS) | FHR EPS |
| HiFill® PA6 GF33 IM L | Techmer Engineered Solutions | Nylon 6 | HiFill® |
| Hifax CA 1110 G4 LS 1740 | LyondellBasell Industries | PP Copolymer | Hifax |
| CYCOLOY™ CY6310 resin | SABIC Innovative Plastics | PC+ABS | CYCOLOY™ |
