LUVOCOM® 100-7126 VP Datasheet,PUR, Unspecified,Lehmann & Voss & Co.-SHANGHAI SUSHENG

Message
LUVOCOM®100-7126 VP is a thermoplastic polyurethane elastomer material,. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific,. LUVOCOM®The main features of 100-7126 VP are: Wear-resistant Lubrication Typical application areas include: engineering/industrial accessories Handle

General Information
Additive	PTFE lubricant
Features	Low friction coefficient Good wear resistance Lubrication
Uses	Handle Roller Bearing
Appearance	Natural color

Physical	Nominal Value	Unit	Test Method
Density	1.26	g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/10.0 kg)	12	g/10 min	ISO 1133
Molding Shrinkage	1.5 - 2.0	%	DIN 16901
Water Absorption (23°C, 24 hr)	< 0.40	%

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A)	82		ISO 868

Mechanical	Nominal Value	Unit	Test Method
Tensile Stress (Break)	24.0	MPa	ISO 527-2
Tensile Strain (Yield)	750	%	ISO 527-2

Impact	Nominal Value	Unit	Test Method
Charpy Unnotched Impact Strength (23°C)	No Break		ISO 179/1fU

Thermal	Nominal Value	Unit	Test Method
Continuous Use Temperature	90.0	°C	UL 746B
Maximum operating temperature- Short Term	120	°C

Electrical	Nominal Value	Unit	Test Method
Insulation Resistance	> 1.0E+12	ohms	IEC 60167

Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature	115	°C	ISO 306/A

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	> 1.0E+12	ohms	IEC 60093

Injection	Nominal Value	Unit
Drying Temperature
Dehumidification desiccant, B	100 - 110	°C
Hot air dryer, A	60.0 - 90.0	°C
Drying Time
Dehumidification desiccant, B	2.0 - 3.0	hr
Hot air dryer, A	2.0 - 3.0	hr
Suggested Max Moisture	0.010	%
Rear Temperature	190 - 230	°C
Middle Temperature	190 - 230	°C
Front Temperature	190 - 230	°C
Nozzle Temperature	200 - 240	°C
Processing (Melt) Temp	225	°C
Mold Temperature	25.0 - 60.0	°C

Injection instructions
General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing, the moisture level should not exceed 0.01%, otherwise molecular degradation may occur. As the material absorbs water very rapidly, originally sealed containers should only be opened immediately before processing. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Injection instructions

General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing, the moisture level should not exceed 0.01%, otherwise molecular degradation may occur. As the material absorbs water very rapidly, originally sealed containers should only be opened immediately before processing. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Category:	PUR, Unspecified , Polyurethane
Manufacturer:	Lehmann & Voss & Co.
Trademark:	LUVOCOM®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	THYWPx_LUVOCOM-100-7126-VP.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
RTP ESD A 100.5	RTP Company	PP, Unspecified	RTP
TARFLON™ NEO RC1700	Idemitsu Kosan Co., Ltd.	PC	TARFLON™
Novodur® 640	Styrolution	ABS	Novodur®
Etinox® EI-6310	Ercros, S.A.	PVC, Flexible	Etinox®
EPO-TEK® 323LP	Epoxy Technology Inc.	Epoxy	EPO-TEK®