Order Products : sales@su-jiao.com
DuraMax™ DMX 8070NC
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Advanced Polymer Alloys |
| Trademark: | DuraMax™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | T5rzz8_DuraMax-DMX-8070NC.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| DuraMax™DMX 8070NC is a thermoplastic elastomer (TPE) material,. This product is available in North America, Europe or Asia Pacific,. |
| General Information | |
|---|---|
| Appearance |
|
| Forms |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.17 | g/cm³ | ASTM D792, ISO 1183 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 69 | ASTM D2240, ISO 868 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Set | 9 | % | ASTM D412 |
| Tensile Stress (100% Strain) | 3.86 | MPa | ASTM D412, ISO 37 |
| Tensile Strength (Yield) | 14.5 | MPa | ASTM D412, ISO 37 |
| Tensile Elongation (Break) | 440 | % | ASTM D412, ISO 37 |
| Tear Strength 1(24°C) | 38.5 | kN/m | ASTM D624 |
| Compression Set | ASTM D395B, ISO 815 | ||
| 24°C, 22 hr | 15 | % | ASTM D395B, ISO 815 |
| 70°C, 22 hr | 56 | % | ASTM D395B, ISO 815 |
| 100°C, 22 hr | 65 | % | ASTM D395B, ISO 815 |
| Clash-Berg Modulus (-27°C) | 68.9 | MPa | ASTM D1043 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength in Air | |||
| 125°C, 168 hr | 6.0 | % | ASTM D573, ISO 188 |
| 100% strain, 125°C, 168 hr | 33 | % | ASTM D573 |
| 100% strain 125°C, 168 hr | 33 | % | ISO 188 |
| Change in Ultimate Elongation in Air (125°C, 168 hr) | 0.0 | % | ASTM D573, ISO 188 |
| Change in Volume | |||
| 24°C, 168 hr, in reference fuel B | -9.0 | % | ASTM D471 |
| 100°C, 168 hr, ASTM Standard Oil (No.1) | -33 | % | ASTM D471 |
| 100°C, 168 hr, IRM 903 Standard Oil (No.3) | -24 | % | ASTM D471 |
| 24°C, 168 hr, in reference fuel B | -9.0 | % | ISO 1817 |
| 100°C, 168 hr, in ASTM #1 oil | -33 | % | ISO 1817 |
| 100°C, 168 hr, in IRM 903 Oil #3 | -24 | % | ISO 1817 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melt Viscosity (149°C, 374 sec^-1) | 300 | Pa·s | ASTM D3835 |
| Additional Information |
|---|
| The value listed as Density -Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.The value listed as Density, ISO 1183, was tested in accordance with ISO 2781. |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 177 | °C |
| Note Message | |
|---|---|
| 1 . | C mould |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Rhelon G2530H-01 | RheTech, Inc. | Nylon 66 | Rhelon |
| Colorite 11 Series 7511 | Colorite Polymers | PVC, Unspecified | Colorite 11 Series |
| DOMAMID® CP7 | DOMO Engineering Plastics SPA | Nylon 6 | DOMAMID® |
| Hostaform® C 9021 TF XAP² ™ | Celanese Corporation | Acetal (POM) Copolymer | Hostaform® |
| KumhoSunny PBT 3730G | Shanghai KumhoSunny Plastics Co., Ltd. | PBT | KumhoSunny PBT |
