Order Products : sales@su-jiao.com
Generic PPE+PS - Unspecified
| Category: | PPE+PS , Polyphenylene Ether + PS |
| Manufacturer: | Generic |
| Trademark: | Generic |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | RynNpY_Generic-PPE-PS---Unspecified.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
This data represents typical values that have been calculated from all products classified as: Generic PPE+PS - Unspecified This information is provided for comparative purposes only. |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density (23°C) | 1.14 - 1.43 | g/cm³ | ISO 1183 |
| Molding Shrinkage (23°C) | 0.22 - 0.60 | % | ISO 294-4 |
| Water Absorption (23°C, 24 hr) | 0.060 | % | ISO 62 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (Yield, 23°C) | 46.0 - 81.4 | MPa | ISO 527-2 |
| Tensile Strain (Break, 23°C) | 2.0 - 2.2 | % | ISO 527-2 |
| Flexural Modulus (23°C) | 2410 - 8500 | MPa | ISO 178 |
| Flexural Stress (23°C) | 86.2 - 151 | MPa | ISO 178 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength (23°C) | 2.8 - 6.5 | kJ/m² | ISO 179 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | |||
| 1.8 MPa, not annealed | 100 - 120 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 96.9 - 119 | °C | ISO 75-2/A |
| CLTE - Flow | 2.9E-5 - 6.0E-5 | cm/cm/°C | ISO 11359-2 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Surface Resistivity | 9.8E+15 - 1.0E+16 | ohms | IEC 60093 |
| Volume Resistivity (23°C) | 1.0E+16 - 1.1E+16 | ohms·cm | IEC 60093 |
| Dielectric Constant (23°C) | 3.00 - 3.41 | IEC 60250 | |
| Dissipation Factor (23°C) | 2.8E-3 - 9.0E-3 | IEC 60250 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 94.3 - 106 | °C | |
| Drying Time | 3.0 - 3.5 | hr | |
| Processing (Melt) Temp | 270 - 275 | °C | |
| Mold Temperature | 65.0 - 80.8 | °C |
| Injection instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic PPE+PS - UnspecifiedThis information is provided for comparative purposes only. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RTP 4000.3 | RTP Company | PPA | RTP |
| Sindustris PP GP3303 | Sincerity Australia Pty Ltd. | PP, Unspecified | Sindustris PP |
| Vyncolit® X620 | Vyncolit N.V. | Phenolic | Vyncolit® |
| Gallonprene® GP520-4502 | Shenzhen Sungallon Rubber & Plastic Corporation Limited | TPE | Gallonprene® |
| Hostacom TRC 787N | LyondellBasell Industries | TPO (POE) | Hostacom |
