Glastic® 1608 Datasheet,Polyester, TS,Bulk Molding Compounds, Inc.-SHANGHAI SUSHENG

Message
Grade 1608 is a very high-strength, general purpose, corrosion-resistant material. Recommended for compression molding only. UL® Recognized. Meets FDA requirements for food contact.

General Information
Filler / Reinforcement	Glass fiber reinforced material
Features	High strength Good corrosion resistance General
Uses	Pump parts Valve/valve components Engineering accessories Container
Appearance	Black Available colors brownish yellow
Forms	BMC-Block Molding Compound
Processing Method	Compression molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.78	g/cm³	ASTM D792
Water Absorption (24 hr)	1.8	%	ASTM D570

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (Compression Molded)	14500	MPa	ASTM D638
Tensile Strength (Yield, Compression Molded)	38.2	MPa	ASTM D638
Flexural Modulus (Compression Molded)	14500	MPa	ASTM D790
Flexural Strength (Compression Molded)	201	MPa	ASTM D790
Compressive Strength	243	MPa	ASTM D695
Shear Strength	77.6	MPa	ASTM D732

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact (Compression Molded)	520	J/m	ASTM D256

Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load (1.8 MPa, Unannealed, Compression Molded)	260	°C	ASTM D648
Thermal Conductivity	0.26	W/m/K	ASTM C177
RTI Elec	54.4	°C	UL 746
RTI	54.4	°C	UL 746

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	8.3E+13 1.5E+15	ohms	ASTM D257
Dielectric Strength ¹	18	kV/mm	ASTM D149
Dielectric Constant			ASTM D150
60 Hz	5.40 4.90		ASTM D150
1 MHz	4.30 4.50		ASTM D150
Dissipation Factor			ASTM D150
60 Hz	0.026 5.0E-3		ASTM D150
1 MHz	8.0E-3 0.12		ASTM D150
Arc Resistance	104	sec	ASTM D495

Flammability	Nominal Value	Unit	Test Method
Flame Rating (1.59 mm)	HB		UL 94
Oxygen Index	22	%	ASTM D2863

Additional Information
Permittivity, ASTM D150, 60 Hz, Condition A: 4.9Permittivity, ASTM D150, 60 Hz, Condition D: 5.4Permittivity, ASTM D150, 1 MHz, Condition A: 4.3Permittivity, ASTM D150, 1 MHz, Condition D: 4.5Insulation Resistance, ASTM D257, Condition A: 150 Ohm x 10e13Insulation Resistance, ASTM D257, Condition C: 8.3 Ohm x 10e13Track Resistance, ASTM D2303: 105 minutesDissipation Factor, ASTM D150, 60 Hz, Condition A: 0.005Dissipation Factor, ASTM D150, 60 Hz, Condition D: 0.026Dissipation Factor, ASTM D150, 1 MHz, Condition A: 0.008Dissipation Factor, ASTM D150, 1 MHz, Condition D: 0.115

Additional Information

Permittivity, ASTM D150, 60 Hz, Condition A: 4.9Permittivity, ASTM D150, 60 Hz, Condition D: 5.4Permittivity, ASTM D150, 1 MHz, Condition A: 4.3Permittivity, ASTM D150, 1 MHz, Condition D: 4.5Insulation Resistance, ASTM D257, Condition A: 150 Ohm x 10e13Insulation Resistance, ASTM D257, Condition C: 8.3 Ohm x 10e13Track Resistance, ASTM D2303: 105 minutesDissipation Factor, ASTM D150, 60 Hz, Condition A: 0.005Dissipation Factor, ASTM D150, 60 Hz, Condition D: 0.026Dissipation Factor, ASTM D150, 1 MHz, Condition A: 0.008Dissipation Factor, ASTM D150, 1 MHz, Condition D: 0.115

Note Message
1 .	Method A (short time)

Category:	Polyester, TS , Thermoset Polyester
Manufacturer:	Bulk Molding Compounds, Inc.
Trademark:	Glastic®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	Qwoylw_Glastic-1608.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
VICOTE® F813Blk	Victrex plc	PEEK	VICOTE®
Wellamid® GF14-60 XE-N	Wellman Engineering Resins	Nylon 6	Wellamid®
Andur 8-6 APSLM/Curene® 442	Anderson Development Company	PUR-Ester/TDI	Andur
Plavis® G40	Comco Nylon GmbH	PI, TP	Plavis®
STYRON™ 2678 MED	Trinseo	PS (GPPS)	STYRON™