TECHNYL® C 52G1 V30 GREY 2408CF Datasheet,Nylon 6,Solvay Engineering Plastics-SHANGHAI SUSHENG

Message
TECHNYL® C 52G1 V30 Grey 2408 CF is a Non-phosphorous and Non-halogenated flame retardant polyamide 6, reinforced with 25% of glass fiber, heat stabilized, for injection moulding. This flame retardant grade with excellent moulding and electrical performance.

General Information
Filler / Reinforcement	Glass fiber reinforced material, 30% filler by weight
Additive	heat stabilizer Flame retardancy
Features	UV Laser Markable Anti-arc Phosphorus content, low (to none) Halogen-free
Uses	Electrical/Electronic Applications
Agency Ratings	EC 1907/2006 (REACH) UL QMFZ2
Appearance	Grey
Forms	Particle
Processing Method	Injection molding
Resin ID (ISO 1043)	PA6-GF30 FR(30)

Physical	Nominal Value	Unit	Test Method
Density	1.38	g/cm³	ISO 1183/A
Water Absorption (23°C, 24 hr)	1.0	%	ISO 62

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (23°C)	7400	MPa	ISO 527-2/1A
Tensile Stress (Break, 23°C)	90.0	MPa	ISO 527-2/1A
Tensile Strain (Break, 23°C)	2.0	%	ISO 527-2

Impact	Nominal Value	Unit	Test Method
Charpy Unnotched Impact Strength (23°C)	35	kJ/m²	ISO 179/1eU

Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
0.45 MPa, not annealed	215	°C	ISO 75-2/Bf
1.8 MPa, not annealed	190	°C	ISO 75-2/Af
Melting Temperature	220	°C	ISO 11357-3

Electrical	Nominal Value	Unit	Test Method
Comparative Tracking Index (Solution A)	500	V	IEC 60112

Flammability	Nominal Value	Unit	Test Method
Flame Rating			UL 94
0.8 mm	V-2		UL 94
1.6 mm	V-2		UL 94
3.2 mm	V-2		UL 94
Glow Wire Flammability Index			IEC 60695-2-12
0.8 mm	960	°C	IEC 60695-2-12
1.6 mm	960	°C	IEC 60695-2-12
3.2 mm	960	°C	IEC 60695-2-12

Injection	Nominal Value	Unit
Drying Temperature	80	°C
Suggested Max Moisture	0.20	%
Rear Temperature	230 - 235	°C
Middle Temperature	235 - 240	°C
Front Temperature	240 - 250	°C
Mold Temperature	60 - 90	°C

Injection instructions
The material is supplied in airtight bags, ready for use. In case that the virgin material has absorbed moisture, it must be dried with a dehumidified air drying equipment, dew point mini -20°C. Recommended time 2-4hInjection Advice: All reinforced flame retardant compounds generate some level of abrasion/corrosion to the steel processing equipment. These issues can be worsened by using incorrect processing conditions (temperatures, residence time, moisture level ...) during the moulding process. Therefore, Solvay recommends to use the advised processing conditions detailed in this technical data sheet. For equipment that comes into contact with molten flame retarded compounds, Solvay advises to use a steel containing high chromium & high carbon content (minimum concentration of 16% Chromium) to prevent corrosion and abrasion. For the correct reference of steel associated to flame retardant compounds processing, please refer to your equipment manufacturers. For Mould Temperature, in the case of parts where the surface roughness is required we can recommend a temperature at 120°C. Of course it should be noted that this improvement in the surface appearance may be at the expense of the cycle time.

Injection instructions

The material is supplied in airtight bags, ready for use. In case that the virgin material has absorbed moisture, it must be dried with a dehumidified air drying equipment, dew point mini -20°C. Recommended time 2-4hInjection Advice: All reinforced flame retardant compounds generate some level of abrasion/corrosion to the steel processing equipment. These issues can be worsened by using incorrect processing conditions (temperatures, residence time, moisture level ...) during the moulding process. Therefore, Solvay recommends to use the advised processing conditions detailed in this technical data sheet. For equipment that comes into contact with molten flame retarded compounds, Solvay advises to use a steel containing high chromium & high carbon content (minimum concentration of 16% Chromium) to prevent corrosion and abrasion. For the correct reference of steel associated to flame retardant compounds processing, please refer to your equipment manufacturers. For Mould Temperature, in the case of parts where the surface roughness is required we can recommend a temperature at 120°C. Of course it should be noted that this improvement in the surface appearance may be at the expense of the cycle time.

Category:	Nylon 6 , Polyamide 6
Manufacturer:	Solvay Engineering Plastics
Trademark:	TECHNYL®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	Q3DZXN_TECHNYLC52G1V30GREY2408CF.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Sylvin 2990-70 Clear	Sylvin Technologies Incorporated	PVC, Unspecified	Sylvin
ADMER™ SE810	Mitsui Chemicals America, Inc.	TPE	ADMER™
Ad-Tech Epoxy EC-412 Fast	Ad-Tech Plastic Systems Corp.	Epoxy	Ad-Tech Epoxy
Plaskolite Acrylic PL-30	Plaskolite, Inc.	Acrylic (PMMA)	Plaskolite Acrylic
SIBUR Synthetic Rubber SSBR-2560 Grade C	SIBUR	SBR, Solution	SIBUR Synthetic Rubber