Order Products : sales@su-jiao.com
Horda E8551
| Category: | PE, Unspecified , Polyethylene |
| Manufacturer: | Horda Cable Compounds |
| Trademark: | Horda |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | OfgcFD_Horda-E8551.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Strippable Semiconductive Shielding E8551 is a crosslinkable, strippable semiconductive compound, designed for both XLPE and EPDM rubber insulated cables and use in both dry and steam curing processes. Specifications: E8551 meets the requirements as below, when optimal processing extrusion and end testing procedure are used: AEIC CS8 (latest edition) BS 6622 IEC 60502 NF C 33-223 NEMA WC 7-1996/ICEA S-95-658 |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.18 | g/cm³ | ASTM D1928 |
| Mooney Viscosity (ML 1+4, 121°C) | 19 | MU | ISO 289 |
| Moisture Content 1 | ppm | Internal method |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Thermosetting (200°C) 2 | 60/20 | % | IEC 60540 |
| Additional Information | Nominal Value | Unit | |
|---|---|---|---|
| Stripping Angle | 180 | ° | |
| Stripping Force 3 | |||
| EPR : 23°C | 1.5 - 2.0 | kN/m | |
| XPLPE : 23°C | 0.7 - 1.0 | kN/m |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 85 - 90 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength | 11.0 | MPa | ASTM D638 |
| Tensile Elongation (Break) | 220 | % | ASTM D638 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength (135°C, 168 hr) | -10 | % | ASTM D471 |
| Change in Ultimate Elongation (135°C, 168 hr) | -30 | % | ASTM D471 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | ASTM D257 | ||
| 23°C | < 5.0E+2 | ohms·cm | ASTM D257 |
| 90°C | < 1.0E+3 | ohms·cm | ASTM D257 |
| 120°C | < 1.0E+3 | ohms·cm | ASTM D257 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | < 40.0 | °C | |
| Cylinder Zone 1 Temp. | 60.0 - 110 | °C | |
| Cylinder Zone 2 Temp. | 60.0 - 110 | °C | |
| Cylinder Zone 3 Temp. | 60.0 - 110 | °C | |
| Cylinder Zone 4 Temp. | 60.0 - 110 | °C | |
| Cylinder Zone 5 Temp. | 60.0 - 110 | °C | |
| Die Temperature | 100 - 130 | °C |
| Extrusion instructions |
|---|
| Neck Temperature: 100 to 130°CHead Temperature: 100 to 130°C |
| Note Message | |
|---|---|
| 1 . | QAHC-10420 (Karl Fischer method) |
| 2 . | 20 N/cm² |
| 3 . | 50 mm/min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Radilon® A ERV1906LK 100 NAT | Radici Plastics | Nylon 66 | Radilon® |
| SLOVALEN® PH 78 FRT 5 | Plastcom | PP, Unspecified | SLOVALEN® |
| ExxonMobil™ LDPE LD 100 Series | ExxonMobil Chemical | LDPE | ExxonMobil™ LDPE |
| Elastron® G P.G401.A70.B | Elastron USA, Inc. | SEBS | Elastron® G |
| Elastron® G G601.A50.N | Elastron USA, Inc. | SEBS | Elastron® G |
