Order Products : sales@su-jiao.com
POLIGOM G/30
| Category: | EPDM , Ethylene Propylene Diene Terpolymer |
| Manufacturer: | Crosspolimeri S.p.A. |
| Trademark: | POLIGOM |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | N7kDO7_POLIGOM-G-30.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
POLIGOM G/30 is a crosslinkable EPR/EPDM. POLIGOM G/30 is a chemically crosslinkable rubber for low voltage cable insulation and sheathing. It is a conveniently grafted compound able to react in presence of moisture and of a catalyst MAC/202, in some case special catalyst MAC/308 PSL (less activity) is necessary. These two compounds, separately stored, must be mixed before starting extrusion in the ratio: GRAFTING/CATALYST 95/5 Certify: HD22.1 EI4 ,EN50363-2-1 EM6, AS/NZS 3808:2000 X-90,R-E-110,E-110-R |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 0.900 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (190°C/5.0 kg) | 2.0 to 6.0 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 82 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (Yield) | 12.0 | MPa | IEC 60811 |
| Tensile Strain (Break) | 800 | % | IEC 60811 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength in Air | IEC 60811 | ||
| 127°C, 40 hr | 0.0 | % | |
| 150°C, 168 hr | -8.0 | % | |
| Change in Tensile Strain at Break in Air | IEC 60811 | ||
| 127°C, 40 hr | 0.0 | % | |
| 150°C, 168 hr | -17 | % |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Hot Set 1 | IEC 60811 | ||
| 250°C | 60 | % | |
| Residual : 250°C | 10 | % |
| Additional Information | Nominal Value | ||
|---|---|---|---|
| Ozone Resistance 2 | pass |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Head Temperature | 210 | °C |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | > 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric Constant (50 Hz) | 2.80 | ASTM D150 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 160 | °C | |
| Cylinder Zone 2 Temp. | 175 | °C | |
| Cylinder Zone 3 Temp. | 190 | °C | |
| Cylinder Zone 4 Temp. | 205 | °C | |
| Die Temperature | 215 | °C |
| Note Message | |
|---|---|
| 1 . | 20 N/cm² |
| 2 . | Test Method : BS 6899 |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| TECHNYL® A R 218 V30 BLACK | Solvay Engineering Plastics | Nylon 66 | TECHNYL® A |
| TRILOY® CF210M | Samyang Corporation | PC+ABS | TRILOY® |
| Badamid® LA70 GF25 H | Bada AG | Nylon 66 | Badamid® |
| KOPET® KP133G15BL | Kolon Plastics, Inc. | PET | KOPET® |
| Kuraray Poval® PVA 220SB | Kuraray Co., Ltd. | PVOH | Kuraray Poval® |
