Order Products : sales@su-jiao.com
AEI SX-0670:CM424
| Category: | XLPE , Crosslinked Polyethylene |
| Manufacturer: | AEI Compounds Limited |
| Trademark: | AEI |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | MAVwd8_AEI-SX-0670-CM424.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Highly flexible, silane crosslinkable, low-smoke, low-toxicity, halogen-free compound for insulation and sheathing A very flexible silane cross-linkable flame-retardant low-smoke halogen-free compound, which has been developed to meet the requirements of limited toxic and corrosive fume emission. This compound is designed for use as both and insulation and sheathing in flexible cords used for appliances. It can also be used as a sheathing material for general power cable use here a combination of high flexibility and good hot deformation characteristics is required. CM424 catalyst masterbatch is normally added at 5% to 95% of SX-0670 graft. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.42 | g/cm³ | BS 2782 620A |
| Melt Mass-Flow Rate (MFR) (150°C/21.6 kg) | 4.0 | g/10 min | Internal method |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | 8.50 | MPa | IEC 60811-1-1 |
| Tensile Strain (Break) | 270 | % | IEC 60811-1-1 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength | IEC 60811-1-2 | ||
| 70°C, 168 hr, in water | -10 | % | IEC 60811-1-2 |
| 100°C, 168 hr | 22 | % | IEC 60811-1-2 |
| Change in Tensile Strain at Break | IEC 60811-1-2 | ||
| 70°C, 168 hr, in water | -15 | % | IEC 60811-1-2 |
| 100°C, 168 hr | -10 | % | IEC 60811-1-2 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deformation (80°C) | pass | IEC 60811-3-1 | |
| Thermoset 1 | IEC 60811-2-1 | ||
| Elongation under load, 20N/cm² : 200°C | 40 | % | IEC 60811-2-1 |
| Permanent elongation after cooling | 0.0 | % | IEC 60811-2-1 |
| Temperature index | 270 | °C | ISO 4589-3 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Head Temperature | 160 | °C |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Oxygen Index | 30 | % | ISO 4589-2 |
| Additional Information |
|---|
| Crosslinking or cure: A satisfactory cure can be obtained either by immersion in hot water or exposure to low pressure stream at a temperature up to 65°C. |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 130 | °C | |
| Cylinder Zone 2 Temp. | 140 | °C | |
| Cylinder Zone 3 Temp. | 145 | °C | |
| Cylinder Zone 4 Temp. | 150 | °C | |
| Die Temperature | 160 | °C |
| Extrusion instructions |
|---|
| Many modern thermoplastic extruders will process the material although a screw designed to give good homogenisation without excessive shear (which could cause unacceptable increases in melt temperature) should be used. An extruder with an L/D ratio (length/diameter) of 15-24 and an extruder screw with a compression ratio 1.2:1 to 2:1 are recommended. |
| Note Message | |
|---|---|
| 1 . | Cure assessment by hot set test (forced cured at 80°C in water) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| MALEX 01FN002 - 5251 | AD majoris | PC | MALEX |
| Novamid® 2330J | DSM Engineering Plastics | Nylon 66/6 | Novamid® |
| Nylene® 5150 HS | Custom Resins Group | Nylon 66 | Nylene® |
| Hostacom TRC 411N G82732 | LyondellBasell Industries | PP, Unspecified | Hostacom |
| Sylvin 9067-80 Grey 9548 | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
