Order Products : sales@su-jiao.com
ASTALAC™ ABS MGF10E
| Category: | ABS , Acrylonitrile Butadiene Styrene |
| Manufacturer: | Marplex Australia Pty. Ltd. |
| Trademark: | ASTALAC™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | I6XCRF_ASTALAC-ABS-MGF10E.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
ASTALAC™ ABS MGF10E is a 10% short fibre length glass filled ABS grade designed for extrusion or moulding into thick sections. This grade features improved rigidity & tensile strength compared to standard ABS extrusion grades, together with a reduced thermal expansion coefficient. These properties are preliminary only, pending full manufacturing runs. Note: The letters "UV" indicate additional UV stabilisation has been added [ ie: ASTALAC™ ABS MGF10EUV ]. |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Uses |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.11 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (220°C/10.0 kg) | 6.0 | g/10 min | ASTM D1238 |
| Molding Shrinkage - Flow (3.00 mm) | 0.30 | % | ASTM D955 |
| Water Absorption (24 hr) | 0.10 | % | ASTM D570 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 104 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength 1(3.20 mm) | 61.0 | MPa | ASTM D638 |
| Tensile Elongation 2(Break, 3.20 mm) | 5.0 | % | ASTM D638 |
| Flexural Modulus 3(3.20 mm) | 3250 | MPa | ASTM D790 |
| Flexural Strength 4(3.20 mm) | 88.0 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact (3.20 mm) | 120 | J/m | ASTM D256 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | ASTM D648 | ||
| 1.8 MPa, Unannealed, 3.20 mm | 92.0 | °C | |
| 1.8 MPa, Unannealed, 6.40 mm | 97.0 | °C | |
| 1.8 MPa, Unannealed, 12.7 mm | 102 | °C | |
| Vicat Softening Temperature | 106 | °C | ASTM D1525 5 |
| CLTE - Flow | 5.5E-5 | cm/cm/°C | ASTM D696 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating (1.60 mm) | HB | UL 94 | |
| Glow Wire Ignition Temperature (1.60 mm) | 550 | °C | AS/NZS 60695 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 85.0 to 90.0 | °C | |
| Drying Time | 3.0 to 6.0 | hr | |
| Cylinder Zone 1 Temp. | 170 to 190 | °C | |
| Cylinder Zone 2 Temp. | 175 to 200 | °C | |
| Cylinder Zone 3 Temp. | 180 to 205 | °C | |
| Cylinder Zone 4 Temp. | 185 to 210 | °C | |
| Cylinder Zone 5 Temp. | 190 to 220 | °C | |
| Melt Temperature | 190 to 230 | °C | |
| Die Temperature | 180 to 220 | °C | |
| Take-Off Roll | 75.0 to 105 | °C | |
| Back Pressure | 10.0 to 25.0 | MPa |
| Note Message | |
|---|---|
| 1 . | 5.0 mm/min |
| 2 . | 5.0 mm/min |
| 3 . | 1.3 mm/min |
| 4 . | 1.3 mm/min |
| 5 . | Loading 1 (10 N) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RTP 200 D MS | RTP Company | Nylon 612 | RTP |
| ETILGUM ME/15 P2Z | Crosspolimeri S.p.A. | TPE | ETILGUM |
| Kostrate® EDGE YP | Plastic Selection Group, Inc. | TP, Unspecified | Kostrate® EDGE |
| Lupolen 3721 C | LyondellBasell Industries | MDPE | Lupolen |
| Deprene 201-64 | Shanghai Lin Gen Rubber Materials Co., Ltd. | PP+EPDM | Deprene |
