Medalist® MD-12360 Datasheet,TPE,Teknor Apex Company-SHANGHAI SUSHENG

Message
Medalist MD-12360 is a clear high performance thermoplastic elastomer, available in NAT and colors, intended for use in medical and healthcare applications. Medalist MD-12360 is a medium hardness, low density grade suitable for injection molding and extrusion.

General Information
Features	Excellent Processability Low Specific Gravity Low density Good disinfection Good flexibility Good adhesion Good chemical resistance Halogen-free Medium hardness
Uses	Drug Medical/nursing supplies
Agency Ratings	ISO 13485
RoHS Compliance	RoHS compliance
Appearance	Clear/transparent
Forms	Particle
Processing Method	Extrusion Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	0.888	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)	1.0	g/10 min	ASTM D1238

Hardness	Nominal Value	Test Method
Durometer Hardness		ASTM D2240
Shaw A, 1 sec	62	ASTM D2240
Shaw A, 5 seconds	60	ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress			ASTM D412
100% strain	2.31	MPa	ASTM D412
200% strain	3.28	MPa	ASTM D412
300% strain	4.62	MPa	ASTM D412
Tensile Strength (Break)	15.2	MPa	ASTM D412
Tensile Elongation (Break)	780	%	ASTM D412

Legal statement
The information and recommendations contained in this bulletin are, to the best of our knowledge, accurate and reliable but no guarantee of their accuracy is made. All products are sold upon condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchaser assumes all risks and liability for the results of use of the products, including use in accordance with seller's recommendations. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention covered by any patent owned by this company or others. There is no warranty of merchantability and there are no other warranties for the products described. For detailed Product Stewardship information, please contact us. Any product of Teknor Apex, including product names, shall not be used or tested in medical or food contact applications without the prior written acknowledgement of Teknor Apex as to the intended use. Please note that some products may not be available in one or more countries.

Legal statement

The information and recommendations contained in this bulletin are, to the best of our knowledge, accurate and reliable but no guarantee of their accuracy is made. All products are sold upon condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchaser assumes all risks and liability for the results of use of the products, including use in accordance with seller's recommendations. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention covered by any patent owned by this company or others. There is no warranty of merchantability and there are no other warranties for the products described. For detailed Product Stewardship information, please contact us. Any product of Teknor Apex, including product names, shall not be used or tested in medical or food contact applications without the prior written acknowledgement of Teknor Apex as to the intended use. Please note that some products may not be available in one or more countries.

Injection	Nominal Value	Unit
Rear Temperature	127 - 149	°C
Middle Temperature	138 - 160	°C
Front Temperature	149 - 171	°C
Nozzle Temperature	171 - 193	°C
Processing (Melt) Temp	171 - 193	°C
Mold Temperature	21 - 38	°C
Injection Pressure	1.38 - 5.52	MPa
Back Pressure	0.172 - 0.689	MPa
Screw Speed	50 - 100	rpm
Cushion	3.81 - 25.4	mm

Injection instructions
Drying is not necessary. However, if moisture is a problem, dry the pellets for 2 to 4 hours at 150°F (65°C).

Extrusion	Nominal Value	Unit
Cylinder Zone 1 Temp.	138 - 149	°C
Cylinder Zone 2 Temp.	149 - 160	°C
Cylinder Zone 3 Temp.	160 - 182	°C
Cylinder Zone 4 Temp.	160 - 182	°C
Cylinder Zone 5 Temp.	171 - 193	°C
Die Temperature	182 - 204	°C

Extrusion instructions
Screw Speed: 30 to 100 rpm

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	Teknor Apex Company
Trademark:	Medalist™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	GqD7ks_MedalistMD12360.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
WELLAMID Nylon 6000 GVS 10/20 HWCP	CP-Polymer-Technik GmbH & Co. KG	Nylon 6	WELLAMID Nylon
Evermore PUR SS-1100	Evermore Chemical Industry Co., Ltd.	PUR, Unspecified	Evermore PUR
Generic PBT - Unspecified	Generic	PBT	Generic
Karina IVORY PVC COMPOUND 70911-35/ 1-HY-AC	Karina Ind. e Com. de Plásticos Ltda	PVC, Unspecified	Karina
Lupolen 2427 K	LyondellBasell Industries	LDPE	Lupolen