Category: | PEI , Polyether Imide |
Manufacturer: | SABIC Innovative Plastics |
Trademark: | ULTEM™ |
Fillers: | - |
Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
Delivery Terms | FOB, CIF, DAP, DAT, DDP |
PDF: | FgRM3L_ULTEM2210resin.pdf ![]() |
PRICE: | Order Products email sales@su-jiao.com |
Message |
---|
20% Glass fiber filled, enhanced flow Polyetherimide (Tg 217C). Resin is RoHS compliant. UL94 V0 and 5VA listing. |
General Information | |
---|---|
Filler / Reinforcement |
|
RoHS Compliance |
|
Processing Method |
|
Physical | Nominal Value | Unit | Test Method |
---|---|---|---|
Density | 1.42 | g/cm³ | ISO 1183 |
Melt Volume-Flow Rate (MVR) (360°C/5.0 kg) | 10.0 | cm³/10min | ISO 1133 |
Molding Shrinkage - Flow 1 | 0.30 - 0.50 | % | Internal method |
Water Absorption | ISO 62 | ||
Saturated, 23°C | 1.0 | % | ISO 62 |
Equilibrium, 23°C, 50% RH | 0.55 | % | ISO 62 |
Hardness | Nominal Value | Unit | Test Method |
---|---|---|---|
Ball Indentation Hardness (H 358/30) | 150 | MPa | ISO 2039-1 |
Mechanical | Nominal Value | Unit | Test Method |
---|---|---|---|
Tensile Modulus | 6800 | MPa | ISO 527-2/1 |
Tensile Stress (Break) | 140 | MPa | ISO 527-2/5 |
Tensile Strain (Break) | 2.0 | % | ISO 527-2/5 |
Flexural Modulus 2 | 6500 | MPa | ISO 178 |
Flexural Stress | 210 | MPa | ISO 178 |
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel) | 17.0 | mg | Internal method |
Impact | Nominal Value | Unit | Test Method |
---|---|---|---|
Charpy Notched Impact Strength (23°C) | 9.0 | kJ/m² | ISO 179/2C |
Charpy Unnotched Impact Strength 3 | ISO 179/1eU | ||
-30°C | 35 | kJ/m² | ISO 179/1eU |
23°C | 35 | kJ/m² | ISO 179/1eU |
Unnotched Izod Impact Strength 4 | ISO 180/1U | ||
-30°C | 30 | kJ/m² | ISO 180/1U |
23°C | 30 | kJ/m² | ISO 180/1U |
Thermal | Nominal Value | Unit | Test Method |
---|---|---|---|
Heat Deflection Temperature 5 | |||
0.45 MPa, unannealed, 100 mm span | 210 | °C | ISO 75-2/Be |
1.8 MPa, unannealed, 100 mm span | 205 | °C | ISO 75-2/Ae |
Vicat Softening Temperature | |||
-- | 223 | °C | ISO 306/A50 |
-- | 212 | °C | ISO 306/B50 |
-- | 218 | °C | ISO 306/B120 |
Ball Pressure Test (125°C) | Pass | IEC 60695-10-2 | |
Linear thermal expansion coefficient | ISO 11359-2 | ||
Flow : 23 to 150°C | 2.5E-5 | cm/cm/°C | ISO 11359-2 |
Horizontal : 23 to 150°C | 6.0E-5 | cm/cm/°C | ISO 11359-2 |
Thermal Conductivity | 0.28 | W/m/K | ISO 8302 |
RTI Elec | 170 | °C | UL 746 |
RTI Imp | 170 | °C | UL 746 |
RTI | 170 | °C | UL 746 |
Electrical | Nominal Value | Unit | Test Method |
---|---|---|---|
Surface Resistivity | > 1.0E+15 | ohms | IEC 60093 |
Volume Resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
Dielectric Strength | IEC 60243-1 | ||
0.800mm, in oil | 34 | kV/mm | IEC 60243-1 |
1.60mm, in oil | 26 | kV/mm | IEC 60243-1 |
3.20mm, in oil | 16 | kV/mm | IEC 60243-1 |
Relative Permittivity | IEC 60250 | ||
50 Hz | 3.10 | IEC 60250 | |
60 Hz | 3.10 | IEC 60250 | |
1 MHz | 3.00 | IEC 60250 | |
Dissipation Factor | IEC 60250 | ||
50 Hz | 8.0E-4 | IEC 60250 | |
60 Hz | 8.0E-4 | IEC 60250 | |
1 MHz | 2.5E-3 | IEC 60250 | |
2.45 GHz | 4.9E-3 | IEC 60250 | |
Comparative Tracking Index | IEC 60112 | ||
-- | 150 | V | IEC 60112 |
Solution B | 100 | V | IEC 60112 |
Flammability | Nominal Value | Unit | Test Method |
---|---|---|---|
Flame Rating | UL 94 | ||
0.410 mm | V-0 | UL 94 | |
1.90 mm | 5VA | UL 94 | |
Glow Wire Flammability Index (3.20 mm) | 960 | °C | IEC 60695-2-12 |
Oxygen Index | 46 | % | ISO 4589-2 |
Injection | Nominal Value | Unit | |
---|---|---|---|
Drying Temperature | 150 | °C | |
Drying Time | 4.0 - 6.0 | hr | |
Suggested Max Moisture | 0.020 | % | |
Hopper Temperature | 80.0 - 120 | °C | |
Rear Temperature | 350 - 400 | °C | |
Middle Temperature | 360 - 410 | °C | |
Front Temperature | 370 - 420 | °C | |
Nozzle Temperature | 360 - 410 | °C | |
Processing (Melt) Temp | 370 - 410 | °C | |
Mold Temperature | 140 - 180 | °C |
Note Message | |
---|---|
1 . | Tensile Bar |
2 . | 2.0 mm/min |
3 . | 80*10*4 sp=62mm |
4 . | 80*10*4 |
5 . | 120*10*4 mm |
Resin Grade | Manufacturer | Category | Trademark |
---|---|---|---|
VENYL SG507 - 8139 | AD majoris | Nylon 6 | VENYL |
Geon™ HTX E1502 | PolyOne Corporation | PVC Alloy | Geon™ HTX |
Latiohm 80-05 CNT GCE/500 | LATI S.p.A. | PPS | Latiohm |
LUVOCOM® 6-8618 | Lehmann & Voss & Co. | Nylon 12 | LUVOCOM® |
EPAMOULD 695A55 | Epaflex Polyurethanes S.R.L. | TPU-Polyester | EPAMOULD |