Order Products : sales@su-jiao.com
ASTAPET™ PC/PET MDA267-A
| Category: | PET , Polyethylene Terephthalate |
| Manufacturer: | Marplex Australia Pty. Ltd. |
| Trademark: | ASTAPET™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | F6HDoq_ASTAPET-PC-PET-MDA267-A.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| ASTAPET™ MDA267 is an alloy of Polycarbonate and 100% recycled polyethylene terephthalate (PET). It is suitable for injection moulding or extrusion. Note: The letters "U" or "W" indicate UV stabilisation has been added [ ie: Astapet™ MDA267-U ]. ASTAPET™ MDA267 is a development grade, the typical values detailed on this data sheet are based on limited data and are subject to frequent review |
| General Information | |
|---|---|
| Recycled Content |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.22 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) | ASTM D1238 | ||
| 250°C/2.16 kg | 2.0 | g/10 min | ASTM D1238 |
| 285°C/2.16 kg | 20 | g/10 min | ASTM D1238 |
| Molding Shrinkage - Flow 1(3.00 mm) | 0.40 - 0.80 | % | ASTM D955 |
| Water Absorption (24 hr) | 0.10 | % | ASTM D570 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 112 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength 2(3.20 mm) | 50.0 | MPa | ASTM D638 |
| Tensile Elongation 3(Break, 3.20 mm) | 200 | % | ASTM D638 |
| Flexural Modulus 4(3.20 mm) | 2200 | MPa | ASTM D790 |
| Flexural Strength 5(3.20 mm) | 76.0 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact (3.20 mm) | 900 | J/m | ASTM D256 |
| Dart Drop Impact (3.20 mm) | 70.0 | J | ASTM D3029 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | ASTM D648 | ||
| 1.8 MPa, unannealed, 3.20mm | 86.0 | °C | ASTM D648 |
| 1.8 MPa, unannealed, 12.7mm | 105 | °C | ASTM D648 |
| Vicat Softening Temperature | 155 | °C | ASTM D1525 6 |
| CLTE - Flow | 6.5E-5 | cm/cm/°C | ASTM D696 |
| Flammability | Nominal Value | Test Method | |
|---|---|---|---|
| Flame Rating (1.60 mm) | HB | UL 94 |
| Additional Information |
|---|
| CLTE, ASTM D696: 6e-5 to 7e-5 cm/cm/°CElongation at Break, ASTM D638, 3.2 mm, 5.0 mm/min: >200%Glow Wire Temperature, AS 2420, 1.6 mm: 550°C |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 120 - 130 | °C | |
| Drying Time | 4.0 - 6.0 | hr | |
| Cylinder Zone 1 Temp. | 200 - 220 | °C | |
| Cylinder Zone 2 Temp. | 230 - 240 | °C | |
| Cylinder Zone 3 Temp. | 240 - 250 | °C | |
| Cylinder Zone 4 Temp. | 245 - 255 | °C | |
| Cylinder Zone 5 Temp. | 250 - 260 | °C | |
| Melt Temperature | 240 - 260 | °C | |
| Die Temperature | 250 - 260 | °C | |
| Take-Off Roll | 75.0 - 100 | °C | |
| Back Pressure | 10.0 - 25.0 | MPa |
| Note Message | |
|---|---|
| 1 . | D2 type |
| 2 . | 5.0 mm/min |
| 3 . | 5.0 mm/min |
| 4 . | 1.3 mm/min |
| 5 . | 1.3 mm/min |
| 6 . | 压 力1 (10N) |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RTP 1700 TFE 15 | RTP Company | PPE+PS | RTP |
| Quadrant EPP CESTICOLOR HD 500 | Quadrant Engineering Plastic Products | HMWPE | Quadrant EPP |
| Tarnamid® T- 27 GF30 FRV0 | Grupa Azoty S.A. | Nylon 6 | Tarnamid® |
| Hanwha Total PP TB51 | HANWHA TOTAL PETROCHEMICALS Co., Ltd. | PP, High Crystal | Hanwha Total PP |
| Kemcor HD 2468 | Qenos Pty Ltd | HDPE Copolymer | Kemcor |
