Order Products : sales@su-jiao.com
NORYL™ WCA901 resin
| Category: | PPE+TPE , Polyphenylene Ether + TPE |
| Manufacturer: | SABIC Innovative Plastics |
| Trademark: | NORYL™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | F1VrWy_NORYLWCA901resin.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| Non-Halogenated flame retardant, flexible NORYL resin intended for evaluation in wire and cable applications, capable of meeting VW-1 and 105°C end use temperature requirements as defined by UL 1581. Good processing performance by using standard extrusion equipment. UL1581 tests conducted on 2.0 mm wire with 0.12 mm x 20 stranded copper conductor. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.10 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (250°C/10.0 kg) | 10 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 30 sec) | 91 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength | |||
| Fracture | 26.0 | MPa | UL 1581 |
| Fracture 1 | 23.0 | MPa | ASTM D638 |
| Fracture, 136°C 2 | 27.0 | MPa | UL 1581 |
| Fracture | 22.0 | MPa | ISO 527-2/50 |
| Tensile Elongation | |||
| Fracture | 190 | % | UL 1581 |
| Fracture 3 | 110 | % | ASTM D638 |
| Fracture, 136°C 4 | 130 | % | UL 1581 |
| Fracture | 95 | % | ISO 527-2/50 |
| Flexural Modulus 5 | |||
| 100mm span | 390 | MPa | ASTM D790 |
| -- | 390 | MPa | ISO 178 |
| Films | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Trouser Tear Resistance | 13.0 | N/mm | ISO 6383-1 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | < -40.0 | °C | ASTM D746 |
| UL Temperature Rating | 105 | °C | UL 1581 |
| Heat Deformation 6(121°C) | 15 | % | UL 1581 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| VW-1 | Pass | UL 1581 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Surface Resistivity | 4.2E+16 | ohms | ASTM D257 |
| Volume Resistivity | 5.1E+15 | ohms·cm | ASTM D257 |
| Relative Permittivity (1 MHz) | 2.70 | IEC 60250 | |
| Dissipation Factor (1 MHz) | 4.0E-3 | IEC 60250 | |
| Comparative Tracking Index | 600 | V | IEC 60112 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating (6.00 mm, Testing by SABIC) | V-0 | UL 94 | |
| Glow Wire Flammability Index (3.00 mm) | 850 | °C | IEC 60695-2-12 |
| Glow Wire Ignition Temperature (3.00 mm) | 775 | °C | IEC 60695-2-13 |
| Oxygen Index | 27 | % | ISO 4589-2 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 75.0 - 85.0 | °C | |
| Drying Time | 5.0 - 7.0 | hr | |
| Suggested Max Moisture | 0.020 | % | |
| Cylinder Zone 1 Temp. | 200 - 240 | °C | |
| Cylinder Zone 3 Temp. | 240 - 270 | °C | |
| Cylinder Zone 5 Temp. | 240 - 270 | °C | |
| Melt Temperature | 240 - 270 | °C | |
| Die Temperature | 240 - 270 | °C |
| Extrusion instructions |
|---|
| Conductor Pre-heat Temperature: 80 - 150 °CCooling Water Air Gap: 100 - 200 mmCross-head Temperature: 240 - 270 °CDrying Time (Cumulative): 12 hrsExtruder Length/Diameter Ratio (L/D): 22:1 to 26:1Neck Temperature: 240 - 270 °CScreen Pack: 150 - 100Screw Speed: 15 - 85 rpmWater Bath Temperature: 15 - 45 °C |
| Note Message | |
|---|---|
| 1 . | Type 1, 50mm/min |
| 2 . | After 7 days |
| 3 . | Type 1, 50mm/min |
| 4 . | After 7 days |
| 5 . | 13 mm/min |
| 6 . | 250 g |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| NOVADURAN® 5010GT15 | Mitsubishi Engineering-Plastics Corp | PBT | NOVADURAN® |
| CPI PP 40 Natural | CPI Binani, Inc. | PP, Unspecified | CPI PP |
| ENVIROPLAS® ENV07-NC520 | ENVIROPLAS®, Inc. | PBT | ENVIROPLAS® |
| Starex TF-0957H | LOTTE ADVANCED MATERIALS CO., LTD. | Acrylic (PMMA) | Starex |
| Kepital® F10-02 | Korea Engineering Plastics Co., Ltd | Acetal (POM) Copolymer | Kepital® |
