Order Products : sales@su-jiao.com
AEI TP536
| Category: | PE, Unspecified , Polyethylene |
| Manufacturer: | AEI Compounds Limited |
| Trademark: | AEI |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | E0g8F4_AEI-TP536.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Thermoplastic, low smoke, halogen free, flame retardant compound for cable insulation and sheathing. This is a flame retardant, low smoke, thermoplastic compound which has been specially developed to meet the requirements of limited toxic and corrosive fume emission, having good moisture resistance and hot pressure performance. TP536 has been specially developed to comply with the requirements of BS7655 Section 6 for types LTS1,2,3 and 4; EN 50290-2-27 for type HM2 and HD 604 for type HM4. TP536 is available in the following versions:
|
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.50 | g/cm³ | BS 2782 620A |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 11 | g/10 min | Internal method |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness | |||
| Shaw A | 90 | ||
| Shaw D | 40 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | 16.0 | MPa | IEC 60811-1-1 |
| Tensile Strain | |||
| Fracture | 160 | % | IEC 60811-1-1 |
| Fracture, -30°C 1 | 60 | % | IEC 60811-1-4 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength (100°C, 168 hr) | 18 | % | IEC 60811-1-2 |
| Change in Tensile Strain at Break (100°C, 168 hr) | -15 | % | IEC 60811-1-2 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deformation (90°C) | 25 | % | IEC 60811-3-1 |
| Cold bending (-30°C) | pass | IEC 60811-1-4 | |
| Temperature index | 280 | °C | ISO 4589-3 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Insulation Constant - Ki | IEC 60502 | ||
| 20°C | 5.4E+9 | ohms·cm | IEC 60502 |
| 90°C | 5.7E+7 | ohms·cm | IEC 60502 |
| Conduction rate- of gases | 10.7 | µS/cm | EN 50267-2-3 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Corrosive gases in flue gas- pH | 4.30 | EN 50267-2-3 | |
| Smoke- 3m cube test | pass | EN 61034 |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Halogen Acid Gas Evolution | % | IEC 60754-1 | |
| Tear Strength | 6.5 | N/mm | BS 6469 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Head Temperature | 160 | °C |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Oxygen Index | 35 | % | ISO 4589-2 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 120 | °C | |
| Cylinder Zone 2 Temp. | 130 | °C | |
| Cylinder Zone 3 Temp. | 140 | °C | |
| Cylinder Zone 4 Temp. | 150 | °C | |
| Melt Temperature | < 170 | °C | |
| Die Temperature | 160 | °C |
| Extrusion instructions |
|---|
| An extruder with an L/D ratio (length/diameter) of 15-24 and an extruder screw with a compression ratio 1.5:1 or less are recommended. |
| Note Message | |
|---|---|
| 1 . | pass |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Ultramid® A27 E | BASF Corporation | Nylon 66 | Ultramid® |
| Adflex KS084P | LyondellBasell Industries | Polyolefin, Unspecified | Adflex |
| LAMIGAMID® 510 | Schwartz Technical Plastic | PET | LAMIGAMID® |
| LNP™ LUBRICOMP™ EL003 compound | SABIC Innovative Plastics | PEI | LNP™ LUBRICOMP™ |
| PALSAFE® R 10 | pal plast GmbH | PC | PALSAFE® |
