Order Products : sales@su-jiao.com
OnFlex™ HT 70A-3S2103
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | OnFlex™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | DmtgP6_OnFlex-HT-70A-3S2103.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
OnFlex™HT thermoplastic elastomer polymer is based on hydrogenated styrene block copolymer. This series of polymers specializes in providing good compression permanent deformation resistance and high heat resistance at high temperatures. In addition, OnFlex™HT polymer conforms to EN 681-2 standard, providing excellent mechanical properties, wide hardness range and good processability. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.00 | g/cm³ | ISO 1183 |
| Molding Shrinkage - Flow (23°C, 2.00 mm) | 1.5 - 1.9 | % | Internal method |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shao A, 3 seconds, 23°C, 6.00mm, injection molding) | 70 | DIN 53505 | |
| IRHD Hardness | 78 | ISO 48 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress 1 | DIN 53504 | ||
| Lateral flow : fracture, 23°C, 2.00mm | 9.40 | MPa | DIN 53504 |
| Traffic : fracture, 23°C, 2.00mm | 7.50 | MPa | DIN 53504 |
| Tensile Elongation 2 | DIN 53504 | ||
| Lateral flow : fracture, 23°C, 2.00mm | 800 | % | DIN 53504 |
| Traffic : fracture, 23°C, 2.00mm | 630 | % | DIN 53504 |
| Tear Strength | 37 | kN/m | ISO 34-1 |
| Compression Set | ISO 815 | ||
| -10°C, 22 hr | 43 | % | ISO 815 |
| 23°C, 72 hr | 25 | % | ISO 815 |
| 70°C, 22 hr | 40 | % | ISO 815 |
| 100°C, 22 hr | 51 | % | ISO 815 |
| Stress relaxation | ISO 3384 | ||
| 23°C 3 | 15 | % | ISO 3384 |
| 23°C 4 | 23 | % | ISO 3384 |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| General Material Type | Styrene thermoplastic elastomers (TES) |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Apparent Viscosity | ASTM D3835 | ||
| 200°C, 1340 sec^-1 | 71.2 | Pa·s | ASTM D3835 |
| 200°C, 11200 sec^-1 | 18.6 | Pa·s | ASTM D3835 |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| 各项属性值是采用注射模制基板测量得出。 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 180 - 220 | °C | |
| Mold Temperature | 30.0 - 60.0 | °C | |
| Injection Rate | Fast |
| Note Message | |
|---|---|
| 1 . | 200 mm/min |
| 2 . | 200 mm/min |
| 3 . | 168 hours, 25% intensity of compression, method A |
| 4 . | 100 days, 25% intensity of compression, method A |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| TYNELOY® NA4200 | Tyne Plastics LLC. | PPE+PS | TYNELOY® |
| ALTECH® PP-H A 2030/158 GF30 CP | ALBIS PLASTIC GmbH | PP Homopolymer | ALTECH® PP-H |
| DIOSHY® MP-930NC | DIOSHY Co.,Ltd. | SBS | DIOSHY® |
| Hyundai EP PPF HT980 | HYUNDAI EP Co., Ltd. | PP Homopolymer | Hyundai EP PPF |
| VALOX™ 451E resin | SABIC Innovative Plastics | PBT | VALOX™ |
