Order Products : sales@su-jiao.com
Elexar® EL-1392B
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Teknor Apex Company |
| Trademark: | Elexar® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | CBKFae_Elexar-EL-1392B.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| RoHS compliant |
| General Information | |
|---|---|
| Uses |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.24 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) (200°C/5.0 kg) | 14 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 87 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (100% Strain) | 3.93 | MPa | ASTM D412 |
| Tensile Strength (Break) | 10.6 | MPa | ASTM D412 |
| Tensile Elongation (Break) | 540 | % | ASTM D412 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength | ASTM D471 | ||
| 131°C, 3600 hr | 6.0 | % | ASTM D471 |
| 136°C, 168 hr | 7.0 | % | ASTM D471 |
| 158°C, 168 hr | -8.0 | % | ASTM D471 |
| Change in Ultimate Elongation | ASTM D471 | ||
| 131°C, 3600 hr | -11 | % | ASTM D471 |
| 136°C, 168 hr | 1.0 | % | ASTM D471 |
| 158°C, 168 hr | -7.0 | % | ASTM D471 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | < -51.0 | °C | ASTM D746 |
| RTI Elec | 50.0 | °C | UL 746 |
| RTI Imp | 50.0 | °C | UL 746 |
| RTI | 50.0 | °C | UL 746 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Dielectric Strength | 39 | kV/mm | ASTM D149 |
| Dissipation Factor (25°C, 1 MHz) | 4.0E-3 | ASTM D150 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating (1.35 to 1.55mm, All Colors) | V-0 | UL 94 | |
| Oxygen Index | 28 | % | ASTM D2863 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Rear Temperature | 199 - 216 | °C | |
| Middle Temperature | 213 - 221 | °C | |
| Front Temperature | 221 - 227 | °C | |
| Nozzle Temperature | 221 - 229 | °C | |
| Processing (Melt) Temp | 221 - 229 | °C | |
| Mold Temperature | 25.0 - 65.6 | °C | |
| Injection Pressure | 1.38 - 6.89 | MPa | |
| Injection Rate | Moderate-Fast | ||
| Back Pressure | 0.172 - 0.345 | MPa | |
| Screw Speed | 50 - 100 | rpm | |
| Cushion | 3.81 - 25.4 | mm |
| Injection instructions |
|---|
| 无需干燥。但如果湿度过大，则将粒料在150°F (65°C)的温度下干燥2-4小时。 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 154 - 166 | °C | |
| Cylinder Zone 2 Temp. | 177 - 193 | °C | |
| Cylinder Zone 3 Temp. | 193 - 204 | °C | |
| Cylinder Zone 5 Temp. | 204 - 213 | °C | |
| Die Temperature | 210 - 221 | °C |
| Extrusion instructions |
|---|
| 螺杆转速30 - 100 rpm |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Santoprene™ 8221-60 | ExxonMobil Chemical | TPV | Santoprene™ |
| WELLAMID Nylon 6000 GV 10 HWCP | CP-Polymer-Technik GmbH & Co. KG | Nylon 6 | WELLAMID Nylon |
| NYCOA Polyamide 5033 HS | Nycoa (Nylon Corporation of America) | Nylon 66 | NYCOA Polyamide |
| Dryflex® A2 602450 | ELASTO | SEBS | Dryflex® |
| DEXFLEX® D60-UV 4LLA | LyondellBasell Industries | TPO (POE) | DEXFLEX® |
